Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Zephyr TWIM too slow so need to use NRFX driver 0

I have an application which is not able to talk with my gas gauge device when the TI EV2400 can. Looking at the waveforms all look the same except for the Zephyr code has...
39 views

0 replies

Started 8 hours ago
by John Galvin
Not Answered
Accessing the USB data lines from the nPM1300EK 0

Is there a recommended way to access the USB data lines from the J3 connector of the nPM1300EK? I would like to be able to charge the battery and also provide a USB mass storage...
- development
- usb
- hardware
- nPM1300
39 views

0 replies

Started 13 hours ago
by Scigrapher
Not Answered
nRF9151 DECT NR+ – PT association fails with MAC_STATUS_NO_RESOURCES (7) using official dect_shell sample 0

Hello, I am currently testing DECT NR+ communication between multiple nRF9151 SMA DK boards, but I am unable to establish a connection between an FT and a PT. I initially...
42 views

0 replies

Started 13 hours ago
by Damntrak06
Not Answered
nRF93M1: Test firmware updates 0

The nRF91 series of modem firmware are distributed with FOTA-TEST diffs to allow for validation of FOTA integrations. Will the nRF93M1 firmware images be distributed with...
34 views

0 replies

Started 15 hours ago
by JordanYates
Not Answered
nRF52840 HCI USB / SDC – How to configure per-connection event length and scheduling 0

Hi Nordic team, I am using the nRF52840 HCI USB project as the controller firmware, with a Linux device acting as the Bluetooth host. My application has multiple BLE connections...
75 views

0 replies

Started 1 day ago
by Dzmitry

Recent in the DevZone Blog

Getting Started with the Thingy:52 and GCC/GDB

Daniel Veilleux

The Thingy:52 IoT Sensor Kit is a fancy development board that combines the nRF52832 SoC, a handful of sensors and user interface components, and a rechargeable battery. Although the Thingy is available…
- 20 Jul 2018
Provision, configure and control Bluetooth mesh networks with nRF Mesh

Petter Myhre

nRF Mesh are open source libraries for building your own Android and iOS Bluetooth mesh apps. It is also the name of the apps demonstrating a subset of the capabilities of the libraries. Use them in test…
- 25 Jun 2018
nRF52832 Buttonless DFU Development Tutorial - GitHub

gamnes

This tutorial is valid as of 2018-06-06, updates to tools and SDKs might have been made since then. Please review the information on http://infocenter.nordicsemi.com/ to see if any updates have been made…
- 12 Jun 2018
Optimizing Power on nRF52 Designs

notsane0

As customers reach the end of their design cycle, their attention generally falls on power optimization, especially for battery powered designs. The following are hints for achieving the lowest possible…
- 30 May 2018
New Smart Remote 3 SDK release enables cost optimized Bluetooth 5 voice remote controls

Pär H

It has been some time since we released new SDK for the nRFready Smart Remote 3 for nRF52 Series. The recently released rev 1.2 of the firmware introduces a lot of new features and improvements. This SDK…
- 24 May 2018
Accurate State of Charge Measurements For Li-Ion Batteries Using a State of Charge vs Open Circuit Voltage Lookup Table

Bjørn Kvaale

We have had a few questions on the Nordic DevZone related to state of charge estimation of Li-Ion batteries when used in conjucture with an nrf52 DK. This blog post will show you how to customize your…
- 14 May 2018