Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
SPI on "low drive, low frequency I/O" pins (P0.26–P0.29) — real max bit rate and RF impact on nRF52832? 0

I am designing a board around the nRF52832 (QFN48). According to Table 5 in the product spec, GPIOs P0.22–P0.31 are marked "Low drive, low frequency I/O only" (see §4.3.1...
17 views

0 replies

Started 39 minutes ago
by hello0
Not Answered
nRF54L05 SAADC current at 2,048 Hz with two-channel scan 0

I need the expected SAADC current for this configuration: • Device: nRF54L05 • Supply: 3.0 V • Internal DC/DC regulator enabled • Resolution: 10 bit • Two enabled analog...
36 views

0 replies

Started 9 hours ago
by Jonsiann
Not Answered
nRF93M1 DK PPP Shell Sample: Unable to Connect to Network 0

Hi Nordic Team, I've just received my nRF93M1 DK. Similar to this issue, I am unable to get my DK connected using the PPP shell sample. Hardware: PCA10232 v0.4.0 Modem...
66 views

0 replies

Started 1 day ago
by Macro Yau
Not Answered
Zephyr TWIM too slow so need to use NRFX driver 0

I have an application which is not able to talk with my gas gauge device when the TI EV2400 can. Looking at the waveforms all look the same except for the Zephyr code has...
83 views

0 replies

Started 1 day ago
by John Galvin
Not Answered
Accessing the USB data lines from the nPM1300EK 0

Is there a recommended way to access the USB data lines from the J3 connector of the nPM1300EK? I would like to be able to charge the battery and also provide a USB mass storage...
- development
- usb
- hardware
- nPM1300
80 views

0 replies

Started 1 day ago
by Scigrapher

Recent in the DevZone Blog

6 Things to Know about Bluetooth Beacons

Rose Martin

Smartphones and tablets have revolutionized the manner in which people communicate with each other. Mobile applications with location-based features like Bluetooth beacons, WiFi, and GPS are helping people…
- 22 Sep 2017
Creating a Keil project for a Bluetooth Mesh example (Updated for 0.10.0)

Kristian Skordal

Introduction The recently released nRF5 SDK for Bluetooth Mesh does not provide Keil project files for its example projects. Fortunately, it's relatively easy to set up your own project from scratch.…
- 19 Sep 2017
Using millis() like in Arduino.

schef

Here are two simple functions to use when you want to use timestamps for time measurement. uint32_t millis(void) { return(app_timer_cnt_get() / 32.768); } and for comperison of current with given…
- 18 Sep 2017
Flashing nRF5x firmware using any dumb terminal program via standard serial COM port

Nguyen Hoan Hoang

There are times that we needed to flash the nRF5x series on a PC where the development software were not installed. The problem could be worst when network access is limited. With a HEX file on hand…
- 18 Sep 2017
How to Debug the nRF52 Interrupts — Useful Tips

Yaniv Nis

Debugging interrupts in not an easy task. During the development of Jumper's Emulator, we gather few useful tips that we think can help you all when debugging the nRF52 interrupts. Hope it will help…
- 13 Sep 2017
The ultimate guide to maximizing your BLE and Bluetooth 5 data throughput

Mohammad Afaneh

In my 2nd blog post in the series on Bluetooth 5, I go over one of the main features of Bluetooth 5: 2x speed. The advertised 2x speed of Bluetooth 5 is great! BUT, what does that even mean? Is it…
- 7 Sep 2017