Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Processing After a UART Error Is Detected 0

Hello. Please explain how to detect errors in UART interrupt-driven operation. If an error is detected by calling `uart_err_check()`, is it necessary to clear the error flag...
- development
- software
- nRF54L05
- zephyr
2 views

0 replies

Started 7 minutes ago
by Fumiya
Not Answered
nRF52832是否支持SCPP和SCPS 0

针对IOPT测试项，若产品支持 SCPP 协议，则此类测试项为必测项，但是SGS机构反馈nRF52832-QFAA并不支持SCPS，请问是nRF52832-QFAA本身不支持SCPS还是需要软件去开启SCPS?
24 views

0 replies

Started 3 hours ago
by hua0
Not Answered
nRF5340 / NCS 3.3.x–3.4.x: MCUboot erases an encrypted staged image instead of swapping it — secure boot + image encryption cannot complete an OTA (+3 related bootloader defects, bench-measured) 0

What this ticket reports We ship a battery-powered nRF5340 product using the nRF Connect SDK's documented production security configuration: immutable bootloader (NSIB/b0...
44 views

0 replies

Started 9 hours ago
by avatarsd
Not Answered
NCS 3.4.0 - Thingy91X - build without SECURE_BOOT_APPCORE fails to flash 0

NCS 3.4.0 - Thingy91X If I configure the sysbuild with sysbuild.conf SB_CONFIG_BOOTLOADER_MCUBOOT=y SB_CONFIG_SECURE_BOOT_APPCORE=n it builds, but on "west flash" I...
26 views

0 replies

Started 12 hours ago
by Achim Kraus
Not Answered
[Bug report] RTT and Flash collision block debug port 0

I am working with the NRF52832 DK with a Tag-Connect 3 prong cable attached to the debug port. I have found a bug that has so far been 100% reproducible. It already happened...
- software
- flash
- nrf52832
- hardware
- production
119 views

0 replies

Started 1 day ago
by Thcrull

Recent in the DevZone Blog

nRF52 Range Extension with RFaxis' RFX2411N

Floyd Ashbaugh

External Power Amplifiers and LNAs easily connected to the nRF52 series device for high power extended range operation. Data sheets, white papers, schematics and layout information available at link t…
- 26 Jan 2016
Developing Nordic nRF51 applications with mbed and Visual Studio

ivan

This tutorial shows how to use the mbed framework to develop applications for Nordic nRF51 devices. Before you begin, install VisualGDB 5.1 or later. Start Visual Studio and open the VisualGDB Embedded…
- 26 Jan 2016
PA / LNA support in S132

Einar Thorsrud

The S132 SoftDevice for the nRF52 has support for enable/disable switching of external Power Amplifiers (PA) and Low Noise Amplifiers (LNA) using GPIO pins. This was introduced in S132 version 2.0.0-7…
- 25 Jan 2016
Step by Step Guide to Setup and Start Developemt with nRF51 or nRF52 DK and IAR

Pratyush Dave

The purpose of this blog is to provide a step by step guide to help a developer, starting off with the Nordic Semiconductor nRF51 DK, to get the necessary tools installed and get the software (SW) development…
- 25 Jan 2016
BLE nrf51 - Multilink NUS central - Connect to many peripherals through NUS service - with Arduino host

Marco Russi

Hi all, I implemented a simple multilink NUS central based on s130 for nrf51 chip-set. It means that this NUS central can connect to several peripherals simultaneously and send data to each one of them…
- 24 Jan 2016
SEGGER Embedded Studio Part 2 - Monitor Mode Debugging

Michael Dietz

This tutorial will take less than 15 minutes. #Motivation Never lose a BLE connection when debugging your applications again! This technique will also be useful for any application using the PWM peripheral…
- 22 Jan 2016