Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
nRF93M1: plans to expose LTE Timing Advance through the AT command interface? 0

Hello Nordic Support, I am developing a cellular positioning solution using an nRF93M1 LTE Cat 1 bis module. I currently use the following command to retrieve the serving...
21 views

0 replies

Started 1 hour ago
by ing-barbiz
Not Answered
Request for RF Tuning Support – nRF54LM20 with nRF21540 FEM 0

Hi, We are experiencing a low RSSI/range issue with our nRF54LM20 module using the nRF21540 FEM. We have already consulted with you regarding the design under Case ID...
65 views

0 replies

Started 1 day ago
by Irfan Memon
Not Answered
Achieving pin retention in nRF54L15 GPIO without hardware pull-up through sys_reboot() 0

Hi, I have encountered a challenge with the nRF54L15 that I am hoping someone might know a solution for! My device has a power enable pin (on GPIO1) that must ideally...
103 views

0 replies

Started 2 days ago
by htownclyde
Not Answered
NRF_MODEM_LIB_MEM_DIAG_ALLOC Kconfig setting needs log but increments the failed allocs (which is not only used for logging statistics but for diagnosis as well). 0

I am using the SDK v3.4.0 LTS for modem error debugging I included: prj.conf I am mapping errors depending on wether memory allocations failed. I am fetching the stats...
86 views

0 replies

Started 2 days ago
by Peter Horauer
Not Answered
An aborted Channel Sounding procedure leaves ~1 mA residual current until reset (SDC 200.12506) 0

If a Channel Sounding procedure is aborted while in flight and the ACL is then disconnected, the device settles at a flat ~1 mA with the CPU asleep in the idle thread and...
111 views

0 replies

Started 3 days ago
by Nat E

Recent in the DevZone Blog

SwiftDuino

Jason

Uses Swift Language to run your Arduino project in your App via bluetooth. https://www.facebook.com/ucxpresso.nrf/posts/1193211740761762
- 15 Dec 2016
Fast Production Screening based upon Bluetooth DTM

Ken L

The challenge As a product is getting into the production phase, the need of a fast and standalone screening facility on the production line arises. Here I'm introducing a production screening setup…
- 9 Dec 2016
I am developing an open source sensor beacon board

zelin

I am developing an open source sensor beacon board named: YS-Beacon which contains: nRF52832 DAPLink - LPC11U35 9-Axis Motion Sensor Ambient Light Sensor、Proximity Sensor and 3D-Gesture Sensor with…
- 2 Dec 2016
nRF52 Rocket: Part I – Introduction to Model Rocketry and its UX Problem

Tony Wu

Official Launch Video Welcome to this 2 or 3-part blog about the nRF52 Rocket, a BLE-enabled model rocket, which you’ve just seen soaring through the air in the video above. In the first part of blog…
- 21 Nov 2016
What to keep in mind when developing your BLE Android app

Hung Bui

BLE is native supported on Android from v4.3. It has been continuously improved as Android evolving. It's getting more and more complex with additional features. It's important that a Bluetooth app should…
- 14 Nov 2016
Get started on PC Software for Mesh and Mesh DFU

David Edwin

nRF-connect-Mesh PC tool allows the user to demonstrate the nRF OpenMesh and the Mesh Device Firmware Update (DFU). The Mesh DFU will be used for nRF OpenMesh and the Bluetooth Mesh when it is made available…
- 11 Nov 2016