Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
How to Configure Device Type via Serial for Matter over Thread Modules? 0

Hello Nordic community, I am currently working on developing applications for Matter over Thread and have set up my ZAP file accordingly. I've successfully flashed two types...
11 views

0 replies

Started 28 minutes ago
by OllLlllO
Not Answered
Does nrf54L15 support PA? 0

Hi， I am looking forward to ncs2.8.0, which was released last Friday. Today I tried nrf54l15 + 2-wire PA but failed to compile successfully. sdk: ncs2.8.0 project: direct_test_mode...
10 views

0 replies

Started 42 minutes ago
by Август
Not Answered
nRF5340 Build Issue 0

I am developing with the nRF5340, but I am encountering an issue where CONFIG_BOOTLOADER_MCUBOOT is not being enabled. Although I have enabled it in the prj.config file as...
9 views

0 replies

Started 1 hour ago
by giun.kim
Not Answered
Antenna for Small USB Receiver 0

Hi, We are designing a USB Receiver based off the Nordic Proprietary Radio + ESB. Do you have any reference designs for a PCB antenna which must be as small as possible...
7 views

0 replies

Started 1 hour ago
by AGeegee
Not Answered
Matter door lock using Bluetooth LE with Nordic UART Service 0

I am try to make Bluetooth LE with Nordic UART Service bondable in to pair with central, not requiring to enter pairing code again and again. I have set followings in prj...
18 views

0 replies

Started 6 hours ago
by BilalAliAhmad

Recent in Nordic blog

Nordic nRF51822 ARM Cortex-M0 Development using emIDE

Hugh

Nordic nRF51822 ARM Cortex-M0 Development using emIDE To avoid the hefty charges with commercial compilers I tried emIDE with some success; here are the settings I used for the EV Kit Official emIDE…
- 22 Oct 2014
Beacon Kit - Mistake in Ref_Design_UG_v1.0

Salman

I connected the programming header as described in "nRF6930_Beacon_Ref_Design_UG_v1.0.pdf" 5.5.4 Programming interface. I was trying to program Beacon Kit but failed many times then I compared it with…
- 10 Oct 2014
SD card interfacing

Salman

Hi, I have written SD & SDHC card routine for reading, writing and erasing data from SD card. It used the hardware SPI of nRF51822. NOTE: 1)Define the PINs of SD card first before initialing. 2)Define…
- 10 Oct 2014

Latest guides

Getting Started : Build NCS application firmware images using Docker

Markus Tacker (he/him)

How to compile a NCS application using Docker so you don't need to install dependencies directly in your system.
- 17 Feb 2020
Software: Using a custom Secure Partition Manager with your application

Heidi-Irene Harvey Sollie

One of the samples available in the nRF Connect SDK is the Secure Partition Manager, which is required to run applications in the nonsecure domain of the CPU. The sample uses the SPM library available in…
- 12 Feb 2020
Getting Started : nRF Connect SDK Bluetooth Low Energy tutorial part 1: Custom Service in Peripheral role

haakonsh

Scope The goal of this tutorial is to set-up your own custom Bluetooth Low Energy service on an nRF5340 acting in a peripheral role. We will set up a new Bluetooth LE project from scratch. The finished…
- 11 Feb 2020
Mesh Networks: Mass Provisioning of Nordic BLE Mesh Nodes

Mark Q

Purpose When creating a mesh network with many nodes, it can take a while to provision each node, especially using PyACI. An alternative is to use a static provisioner that provisions the nodes automatically…
- 8 Feb 2020
Software and Protocols: Enabling and testing TLS in mqtt_simple

Daniel Veilleux

The MQ Telemetry Transport (MQTT) protocol is hugely popular in IoT because it is lightweight and versatile. In this post we will enable Transport Layer Security (TLS) in the mqtt_simple sample from the…
- 4 Feb 2020
Getting Started: Introduction to Nordic nRF5 SDK and Softdevice

Mihua

What is the difference between SDK and Softdevice? How can we select SDK and Softdevice versions? Do the SoC, SDK, and Softdevice have version compatibility problems? How can we understand the SDK directory…
- 15 Jan 2020