Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
UART configuration in a runtime 0

Hello, My board contains nRF9160 and two nRF52840. One of nRF52840 is a HCI controller (based on HCI lpuart example). nRF9160 communicates with each nRF52840 over separate...
- development
- nRF9160
- configuration
- C
- zephyr
- nrf52840
- dfu
5 views

0 replies

Started 9 minutes ago
by tdfilip
Not Answered
how to over write data in same offset into internal flash on zephyr 0

Hi, I am using the nRF Connect SDK 2.6.1 with the nRF5340 board. I referred to the soc_flash_nrf example to read and write data into flash. I need to overwrite data...
13 views

0 replies

Started 1 hour ago
by ChiragBhavsar
Not Answered
Wireshark : Encrypted packet decrypted incorrectly (bad MIC) and Empty PDU 0

Hi, I have difficulties to sniff BLE packets with nRF52840 and wireshark between a remote controller and phone. I can capture all the pairing process, I see DHKey exchange...
16 views

0 replies

Started 1 hour ago
by MalloryLP
Not Answered
Partition map migratation from ncs 2.2 -> ncs 2.7 (sysbuild) 0

Hi, I have a firmware running on ncs 2.2 with mcuboot and tfm which I'm in the process of upgrading to ncs 2.7 with sysbuild. I currently have a problem converting the...
23 views

0 replies

Started 2 hours ago
by Christoffer Brask
Not Answered
nrf52840 dk to upload code to nrf52811 0

Hi This is my first project to make my custom PCB. I have a question about how can I uploaded my code with segger embedded studio by using nrf52840 dk? For the hardware...
- development
- software
- softdevice
- nrf52840
- nRF52811
20 views

0 replies

Started 2 hours ago
by nordicDK

Recent in Nordic blog

nRF52832 Buttonless DFU Development Tutorial - GitHub

gamnes

This tutorial is valid as of 2018-06-06, updates to tools and SDKs might have been made since then. Please review the information on http://infocenter.nordicsemi.com/ to see if any updates have been made…
- 12 Jun 2018
Optimizing Power on nRF52 Designs

notsane0

As customers reach the end of their design cycle, their attention generally falls on power optimization, especially for battery powered designs. The following are hints for achieving the lowest possible…
- 30 May 2018
New Smart Remote 3 SDK release enables cost optimized Bluetooth 5 voice remote controls

Pär H

It has been some time since we released new SDK for the nRFready Smart Remote 3 for nRF52 Series. The recently released rev 1.2 of the firmware introduces a lot of new features and improvements. This SDK…
- 24 May 2018

Latest guides

Software: Using nRF Connect SDK and west to compile and program the DTM example into the nRF52840 DK

Jay Tyzzer

Background There is a need to enable Nordic hardware with the Direct Test Mode (DTM) firmware. This is so the physical layer and RF characteristics may be ascertained as set in the Bluetooth Sig Specification…
- 14 Apr 2022
Software Development Kit: nRF5 SDK v17.1.0 Secure DFU Hands-on Tutorial for the nRF52810

notsane0

Requirements This document uses: Segger Embedded Studio (SES) nRF5 SDK v17.1.0 an nRF52 DK to emulate the nRF52810 a BLE-enabled mobile device You may want to review the blog here for a more comprehensive…
- 8 Apr 2022
Software Development Kit: nRF5 SDK v17.1.0 Secure DFU Hands-on Tutorial

notsane0

Requirements This hands-on tutorial uses: Segger Embedded Studio (SES) nRF5 SDK v17.1.0 an nRF52840 DK a BLE-enabled mobile device You can use an nRF52 DK or nRF52833 DK instead of the nRF52840 DK,…
- 8 Apr 2022
Software: Building a Bluetooth application on nRF Connect SDK - Part 3 Optimizing the connection

Hung Bui

This is part 3 of the series Building a Bluetooth application on nRF Connect SDK You can find other parts here: Part 1 - Peripheral Role. Part 2 - Central Role. In Part 1 we covered the generic architecture…
- 21 Feb 2022
Peripherals And RF Test: Using Bluetooth Shell

Mark Q

Purpose The purpose of this guide is to demonstrate the use of Bluetooth Shell. Bluetooth Shell (BT Shell) is a command-line shell application that runs over the UART. It allows one to manually type in…
- 21 Jan 2022
Software: Memory Optimization with the nRF Connect SDK

matt.heins

Out of the box, the examples in the nRF Connect SDK are configured for ease of use, functionality, and debugging; they are not generally configured for optimal memory utilization. Some of the examples…
- 6 Jan 2022