Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
SB_CONFIG_MCUBOOT_HARDWARE_DOWNGRADE_PREVENTION + SB_CONFIG_MERGED_HEX_FILES fails to configure without NSIB 0

Setup: nRF Connect SDK v3.4.0 (LTS), custom board based on nRF54LM20A, sysbuild with MCUboot as the only bootloader (no NSIB / b0), DTS partitions (SB_CONFIG_PARTITION_MANAGER...
25 views

0 replies

Started 8 hours ago
by Konstantin Klitenik
Not Answered
Two-chip design (nRF54L + nRF9151): best configuration, handle FOTA of both firmwares over NB-IoT and over BLE 0

Hi, We are designing a battery-powered product based on two Nordic chips and would like your recommendation on the overall architecture before we freeze the hardware, having...
- development
- nb-iot
- nRF9151
- bluetooth le
- hardware
- nRF54L10
35 views

0 replies

Started 10 hours ago
by ruben94m
Not Answered
nRF93M1 mfw 1.5.0: TERMINAL CAPABILITY IPAd bit for SGP.32 eUICCs 0

Hi, GSMA SGP.32 v1.3 section 3.8.2 and 3.8.4: the device selects IPAd or IPAe mode with the TERMINAL CAPABILITY command at UICC initialisation. Tag 84 , byte 1, bit 1 set...
31 views

0 replies

Started 11 hours ago
by erkkie
Not Answered
I2S, or SPI Compatibility with PCM Short, and Long Synch frames 0

Hello I'm developing a project that would communicate with a cellular module using AT-Commands, and voice data using PCM, these cellular modules are always using PCM Short...
35 views

0 replies

Started 13 hours ago
by Beshoy
Not Answered
nPM1300 fuel gauge: SoC rises by 10–28 % after every wake-up, and IBAT reads ~0.57x the real current 0

Problem: After every wake-up our device reports a SoC 10–28 % higher than it reported just before going to sleep. Between sessions the nRF5340 is in System OFF via sys_poweroff...
50 views

0 replies

Started 14 hours ago
by Oleksii Shcherbyna

Recent in the DevZone Blog

Thingy:52 MOSFET Usage

gamnes

This blog post describes how you can take advantage of the 4 MOSFET's on the Thingy:52. DISCLAIMER: Please verify all information that is used/retrieved from this blog post. Some of the information…
- 27 Dec 2018
Using the Power Profiling Kit to measure Current Draw on an External Device

notsane0

The Power Profiler Kit (PPK) is a flexible tool for measuring the real-time current draw of nRF5x designs. When used as an add-on board to measure the nRF5x current of an attached development kit (DK)…
- 26 Dec 2018
What impact does the deprecation and withdrawal of Bluetooth Core specification v4.0 and v4.1 have on your current and future products?

Petter Myhre

This blog was last updated 17.01.2019. The Bluetooth Special Interest Group (SIG) recently announced the deprecation and withdrawal of Bluetooth Core specifications v4.0 and v4.1. For products that are…
- 30 Oct 2018
The S132 v5.1.0 is now production tested on nRF52810

Petter Myhre

This blog describes how you can setup a Segger Embedded Studio example for PCA10040E (emulating nRF52810) from nRF5 SDK 14.2 to use S132 v5.1.0, instead of S112. The procedure should be similar for the…
- 12 Sep 2018
Adding custom commands to a BLE example using Nordic UART Service

Håvard

A common thing to do is to use the Nordic UART Service for quick prototyping. Often the example itself is used as a starting point (ble_app_uart). But sometimes we use other starting points, and want to…
- 6 Sep 2018
Using Two-Factor Authentication (2FA) with the Nordic DevZone

esivertsen

Did you know you can use two-factor authentication to enhance the security of your DevZone account? In this little blog, I’ll show you how to enable Two-Factor Authentication (2FA) with your DevZone account…
- 30 Aug 2018