Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Request for RF Tuning Support – nRF54LM20 with nRF21540 FEM 0

Hi, We are experiencing a low RSSI/range issue with our nRF54LM20 module using the nRF21540 FEM. We have already consulted with you regarding the design under Case ID...
12 views

0 replies

Started 47 minutes ago
by Irfan Memon
Not Answered
Achieving pin retention in nRF54L15 GPIO without hardware pull-up through sys_reboot() 0

Hi, I have encountered a challenge with the nRF54L15 that I am hoping someone might know a solution for! My device has a power enable pin (on GPIO1) that must ideally...
68 views

0 replies

Started 22 hours ago
by htownclyde
Not Answered
l0destar - ultra low-power open-source hardware and software vehicle tracker you can build at home 0

Hi This isn't about a problem so I'm not sure if this is an inappropriate post to make here, if so please feel free to remove it, however there is no commercial incentive...
68 views

0 replies

Started 1 day ago
by m4rkw
Not Answered
NRF_MODEM_LIB_MEM_DIAG_ALLOC Kconfig setting needs log but increments the failed allocs (which is not only used for logging statistics but for diagnosis as well). 0

I am using the SDK v3.4.0 LTS for modem error debugging I included: prj.conf I am mapping errors depending on wether memory allocations failed. I am fetching the stats...
67 views

0 replies

Started 1 day ago
by Peter Horauer
Not Answered
An aborted Channel Sounding procedure leaves ~1 mA residual current until reset (SDC 200.12506) 0

If a Channel Sounding procedure is aborted while in flight and the ACL is then disconnected, the device settles at a flat ~1 mA with the CPU asleep in the idle thread and...
100 views

0 replies

Started 1 day ago
by Nat E

Recent in the DevZone Blog

Getting Started with the Thingy:52 and GCC/GDB

Daniel Veilleux

The Thingy:52 IoT Sensor Kit is a fancy development board that combines the nRF52832 SoC, a handful of sensors and user interface components, and a rechargeable battery. Although the Thingy is available…
- 20 Jul 2018
Provision, configure and control Bluetooth mesh networks with nRF Mesh

Petter Myhre

nRF Mesh are open source libraries for building your own Android and iOS Bluetooth mesh apps. It is also the name of the apps demonstrating a subset of the capabilities of the libraries. Use them in test…
- 25 Jun 2018
nRF52832 Buttonless DFU Development Tutorial - GitHub

gamnes

This tutorial is valid as of 2018-06-06, updates to tools and SDKs might have been made since then. Please review the information on http://infocenter.nordicsemi.com/ to see if any updates have been made…
- 12 Jun 2018
Optimizing Power on nRF52 Designs

notsane0

As customers reach the end of their design cycle, their attention generally falls on power optimization, especially for battery powered designs. The following are hints for achieving the lowest possible…
- 30 May 2018
New Smart Remote 3 SDK release enables cost optimized Bluetooth 5 voice remote controls

Pär H

It has been some time since we released new SDK for the nRFready Smart Remote 3 for nRF52 Series. The recently released rev 1.2 of the firmware introduces a lot of new features and improvements. This SDK…
- 24 May 2018
Accurate State of Charge Measurements For Li-Ion Batteries Using a State of Charge vs Open Circuit Voltage Lookup Table

Bjørn Kvaale

We have had a few questions on the Nordic DevZone related to state of charge estimation of Li-Ion batteries when used in conjucture with an nrf52 DK. This blog post will show you how to customize your…
- 14 May 2018