Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
SPI_NOR was assigned the value 'y' but got the value 'n' based on DT_HAS_JEDEC_SPI_NOR_ENABLED using a W25Q128JV with compatible = "jedec,spi-nor" 0

I am getting an error warning: SPI_NOR (defined at soc/gaisler/gr716a/Kconfig.defconfig:18, drivers/flash/Kconfig.nor:6) was assigned the value 'y' but got the value ...
- development
- software
- zephyr
- nRF5340
9 views

0 replies

Started 51 minutes ago
by lcj
Not Answered
Power consumption on nrf5340 when idle is about 4mA, how to get it lower? 0

I have a custom board, with nrf5340, nrf7002 on it. I would like to get the uA levels of power consumption I see other nrf5340 projects talk about (eg here ) when my application...
11 views

0 replies

Started 1 hour ago
by BrianW
Not Answered
Interfacing nRF54L15 from nRF9151 without Custom Firmware 0

Hi, We are looking to add an nRF54L15 chip to our custom nRF9151 board, to support Bluetooth. We also would like to add NFC functionality and additional GPIO pins from...
16 views

0 replies

Started 3 hours ago
by taylor_ca
Not Answered
Message relay set up 0

Hi there I'm using two nRF52840 boards and I want to set them up to relay a message from one phone to another like this: phoneA > board1 > board2 > phoneB. I have looked...
13 views

0 replies

Started 3 hours ago
by unistudent01
Not Answered
Use of FDS for larger data block 0

Hello, I am working on an update of older FW implementation: nRF52832, SDK 14.1.0, with SoftDevice S132 and using BLE connection. The change I need to implement is a functionality...
- development
- software
- flash
- s132
- nrf52832
- bluetooth le
15 views

0 replies

Started 3 hours ago
by Peter.J

Recent in Nordic blog

Developing Nordic nRF51 Projects with Visual Studio

ivan

This tutorial shows how to create and debug a basic project for the Nordic nRF51-DK using Visual Studio. Before you begin, install VisualGDB 5.0 or later. Start Visual Studio and begin creating a new…
- 6 Aug 2015
Motor Control over BLE with nRF51822 and TB6612FNG

Mahesh Venkitachalam

In this project, we will control two motors over BLE using the Nordic nRF51-DK. To do this, we will use a motor driver based on the Toshiba TB6612FNG chip. We will use GPIOs and PWM to communicate with…
- 5 Aug 2015
Create Hurricane Tunnel Broker on Raspberry Pi

Eugene Yu

This blog introduces how to create tunnel broker service in order to support IPv6 on your IPv4 network. The tunnel broker is providing IP conversion service with 6in4. Preparation Raspberry Pi…
- 4 Aug 2015

Latest guides

nRF5x: Automating Power Profiler Kit measurements from the command line

Daniel Veilleux

Nordic's Power Profiler Kit (PPK) is an inexpensive piece of hardware that can provide a significant amount of insight into the operation and performance of your project. Although there is a lot that…
- 2 Aug 2019
Software and Protocols: How to connect nRF9160 DK to Google Cloud

Marte Myrvold

This project was originally made in an outdated version of NCS, but it has now been updated to NCS v1.5.0. The instructions are the same as before, but the code is different. Disclaimer: This is a student…
- 17 Jul 2019
Mesh Networks: Automating Nordic BLE Mesh Provisioning

Mark Q

Purpose This document will show how to automate the provisioning process for Nordic BLE Mesh nodes using Python scripting. When provisioning nodes using PyACI (Python Application Controller Interface)…
- 8 Jul 2019
Bluetooth low energy: MIDI over Bluetooth LE

Håvard

I implemented parts of the BLE-MIDI service along with a small example application. I wanted to share it here on the blog, in case someone would find it useful. The intended audience is primarily someone…
- 30 Jun 2019
Mesh Networks: Thread Tutorial: Practical guide for device upgrade OTA

AndreasF

This getting started guide is meant as a more detailed practical guide for the Thread Secure DFU Example found on Infocenter which demonstrates upgrade of firmware over the air (OTA). For any questions…
- 7 Jun 2019
Mesh Networks: Zigbee Tutorial: Practical guide for device upgrade OTA

AndreasF

This getting started guide is meant as a more detailed practical guide for the Zigbee OTA (Over the Air) Upgrade Client Example found on Infocenter. If you have any questions regarding Zigbee or Zigbee…
- 27 May 2019