Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Sleep does not work with BLE advertise 0

Hi, nRF52832, SDK 17.1.0 with Softdevice S132. Softdevice sleep does not work when advertising. Application flow is to advertise one packet, then go to sleep for X seconds...
0 views

0 replies

Started 11 minutes ago
by silvio3105
Not Answered
DC/DC higher consumption than LDO 0

Hi, when DC/DC is enabled, current consumption in sleep is higher than when using LDO. This is consumtion with DCDC = 0 This is power consumtion when DCDC =...
0 views

0 replies

Started 36 minutes ago
by silvio3105
Not Answered
Using radio_test to test communication between two devices 0

Previously, I compiled and downloaded the radio_test example into two DK boards. I then used the CLI to set the parameters for each board one as TX one as RX On setting...
0 views

0 replies

Started 2 hours ago
by araucaria
Not Answered
npm1300 on-off switch question 0

Hello, I was wondering if there was a way to implement a physical on/off switch to the npm1300 that would allow the outputs to be isolated form the battery but still having...
0 views

0 replies

Started 4 hours ago
by ecp
Not Answered
nrfjprog command to nrfutil command 0

I'm looking for an nrfutil command to replace this command: nrfjprog --memwr 0x10001080 --val 0x12345678 My goal is to write a serial number to the UICR CUSTOMER[0] register...
0 views

0 replies

Started 5 hours ago
by Phattaw

Recent in Nordic blog

ROM and RAM Management

Øyvind Karlsen

Introduction Here are some tips and tricks to manage your application size. RAM and ROM usage The total RAM usage is: ZI-data + RW-data The total flash usage is: Code + RO-data + RW-data …
- 28 Jul 2015
Controlling an RGB LED with Nordic nRF51-DK

Mahesh Venkitachalam

Using PWM and Nordic UART Service on nRF51-DK (nRF51822/nRF52422) to control an RGB LED over BLE. http://electronut.in/nrf51-rgb-led-test/
- 25 Jul 2015
Intro to Application-level Security Using the ECB Peripheral

Daniel Veilleux

Obligatory Disclaimer Security is hard. If a product handles sensitive information then it is the engineer's responsibility to his customers to consult a security professional. However, experimenting…
- 22 Jul 2015

Latest guides

nRF5x: Automating Power Profiler Kit measurements from the command line

Daniel Veilleux

Nordic's Power Profiler Kit (PPK) is an inexpensive piece of hardware that can provide a significant amount of insight into the operation and performance of your project. Although there is a lot that…
- 2 Aug 2019
Software and Protocols: How to connect nRF9160 DK to Google Cloud

Marte Myrvold

This project was originally made in an outdated version of NCS, but it has now been updated to NCS v1.5.0. The instructions are the same as before, but the code is different. Disclaimer: This is a student…
- 17 Jul 2019
Mesh Networks: Automating Nordic BLE Mesh Provisioning

Mark Q

Purpose This document will show how to automate the provisioning process for Nordic BLE Mesh nodes using Python scripting. When provisioning nodes using PyACI (Python Application Controller Interface)…
- 8 Jul 2019
Bluetooth low energy: MIDI over Bluetooth LE

Håvard

I implemented parts of the BLE-MIDI service along with a small example application. I wanted to share it here on the blog, in case someone would find it useful. The intended audience is primarily someone…
- 30 Jun 2019
Mesh Networks: Thread Tutorial: Practical guide for device upgrade OTA

AndreasF

This getting started guide is meant as a more detailed practical guide for the Thread Secure DFU Example found on Infocenter which demonstrates upgrade of firmware over the air (OTA). For any questions…
- 7 Jun 2019
Mesh Networks: Zigbee Tutorial: Practical guide for device upgrade OTA

AndreasF

This getting started guide is meant as a more detailed practical guide for the Zigbee OTA (Over the Air) Upgrade Client Example found on Infocenter. If you have any questions regarding Zigbee or Zigbee…
- 27 May 2019