Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
nRF54L15 DK: Zephyr POSIX UDP socket over OpenThread/NAT64 sends CoAP successfully, but poll()/recv() does not receive returned packet 0

Hello Nordic team, I am testing a plain CoAP telemetry upload from an nRF54L15 DK over Thread using a Raspberry Pi OTBR and NAT64 to ThingsBoard Cloud. Hardware / software...
9 views

0 replies

Started 40 minutes ago
by MarkusK
Not Answered
How to Set TX Power for Response Packets in periodic_sync_conn? 0

HI I am currently using the nRF54L15 chip with NCS 3.2.1, carrying out secondary development based on the periodic_sync_conn sample project. I intend to adjust the transmit...
11 views

0 replies

Started 51 minutes ago
by joey
Not Answered
Synchronization over LTE/NB-IoT - SNTP time accuracy 0

Hi, We are developing an application that requires synchronization between two or more nRF9160-based devices. We have the following requirements and constraints: Required...
29 views

0 replies

Started 2 hours ago
by mjaszczykowski
Not Answered
ALIRO: Expose session error code to the application 0

I'm using the prebuilt Aliro stack (libaliro.a, nRF52840), when a session fails inside the library we have no way to get the resulting AliroErrorCode. The stack entry points...
48 views

0 replies

Started 6 hours ago
by Jason
Not Answered
nRF9151 modem faults on v2.0.2 0

Hi, We have deployed some devices now, and we see quite some modem faults popping up. Could you try to give all info on what you know about these faults we have from...
55 views

0 replies

Started 19 hours ago
by klaasg

Recent in the DevZone Blog

The S132 v5.1.0 is now production tested on nRF52810

Petter Myhre

This blog describes how you can setup a Segger Embedded Studio example for PCA10040E (emulating nRF52810) from nRF5 SDK 14.2 to use S132 v5.1.0, instead of S112. The procedure should be similar for the…
- 12 Sep 2018
Adding custom commands to a BLE example using Nordic UART Service

Håvard

A common thing to do is to use the Nordic UART Service for quick prototyping. Often the example itself is used as a starting point (ble_app_uart). But sometimes we use other starting points, and want to…
- 6 Sep 2018
Using Two-Factor Authentication (2FA) with the Nordic DevZone

esivertsen

Did you know you can use two-factor authentication to enhance the security of your DevZone account? In this little blog, I’ll show you how to enable Two-Factor Authentication (2FA) with your DevZone account…
- 30 Aug 2018
Introduction of SDH and SDK v15.0 software architecture

Amos Lin

The SDK software architecture has been hugely changed since SDK v13.0. With adding SDH to SDK, it provides SDH API to Enabling the SoftDevice and its event interrupt. Disabling the SoftDevice. Receiving…
- 13 Aug 2018
Bluetooth pairing vulnerability

PaKa

The Bluetooth SIG released an errata for the 4.2 and 5.0 versions of Bluetooth specification on July 23rd relating to a potential vulnerability with the pairing procedures. For Bluetooth low energy; this…
- 27 Jul 2018
Getting Started with the Thingy:52 and GCC/GDB

Daniel Veilleux

The Thingy:52 IoT Sensor Kit is a fancy development board that combines the nRF52832 SoC, a handful of sensors and user interface components, and a rechargeable battery. Although the Thingy is available…
- 20 Jul 2018