Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Bus fault on nRF52840 peripheral in BLE HCI USB Raw mode with 251-byte packets 0

While running the BLE HCI USB ( bluetooth_hci_usb ) sample in Raw mode on an nRF52840 board, we observe a bus fault under specific conditions. The fault occurs when the device...
7 views

0 replies

Started 2 hours ago
by SaleemN
Not Answered
nrf_pwr_mgmt_run(); is not executing in NRF52810 0

I’m working on an nRF52-based design where the device should remain in System ON low-power mode after an operation (SAADC sampling + BLE sync). After SAADC data collection...
17 views

0 replies

Started 7 hours ago
by Tapan Nayak
Not Answered
FPROTECT for NRF54L10 0

I'm working with NRF54L10 module. I needed more mcuboot space so in pm_static.yml I allocated it 80kb. Before this FPROTECT was working but after I allocated 80kb, now FPROTECT...
10 views

0 replies

Started 9 hours ago
by Amaan Singh
Not Answered
how to connect nrf52840 into mesh of 50 device 0

how to create the nrf52840 mesh of more than 50 devices ? I am using the chat sample for this mesh network but i am tested with the 12 boards but i am getting reply from...
12 views

0 replies

Started 13 hours ago
by sibi
Not Answered
zephyr/samples/net/cloud/aws_iot_mqtt fails to connect to aws 0

I have nordic board nrf5340-dk + nrf7002-ek I want to run on it the application zephyr/samples/net/cloud/aws_iot_mqtt I built the project and I flashed on my device I can...
- software
- Evaluation
- Wi-Fi
- zephyr
- nRF5340
22 views

0 replies

Started 13 hours ago
by MOHAMED Kallel

Recent in the DevZone Blog

Programming nRF52832 boards in Python with Zerynth

lfcerf

Released in December 2016, the new Bluetooth 5 offers truly exciting possibilities for home, industry, and commerce as well as the more traditional areas of wearables and personal devices historically…
- 7 Jun 2017
Serial Wire Debug Port Interface for nRF52832

gamnes

1.1 Description This documentation describes the use and initialization of the Serial Wire Debug Port (SWDP) interface when writing to or reading from Flash and SRAM of the nRF52832 Rev 1. See http:/…
- 2 Jun 2017
nRF52840 GATT Data Throughput with Zephyr RTOS

vich

Nordic has recently contributed support for the 2Mbit/s PHY, part of the Bluetooth 5.0 specification, to the Zephyr Project RTOS. The video below shows how to configure, build and test GATT data throughput…
- 2 Jun 2017
The complete tutorial for developing and debugging nRF52 applications on a Mac

Mohammad Afaneh

I realize that there are already multiple tutorials on how to configure GCC along with Eclipse or SEGGER Embedded Studio (for use on a Mac), but this tutorial goes over setting up a different IDE. The…
- 11 May 2017
Bluetooth 5 2Mbps Demo with nRF52 Series and Samsung Galaxy S8

John Leonard

Bluetooth 5 - now arriving in smartphones As we know, Bluetooth 5 was launched last December by the Bluetooth SIG. The nRF52 Series from Nordic have always had Bluetooth 5 and its arrival in the mix for…
- 9 May 2017
Setting up Segger on a mac or pc and debug - step by step for humans

Lola

Most guides out there are unclear and made for machines. Here is a full guide how to setup Segger for mac OS X with some example project from the SDK ( or even a PC but not tested), and also how to debug…
- 5 May 2017