Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Matter Thermostat build fail for nRF54L15DK 0

I'm using NCS SDK v3.0.2 and trying to build the Matter Thermostat example for the target: ` nrf54L15DK/nrf54L15/cpuapp/ns ` However, the build fails with the following errors...
28 views

0 replies

Started 18 hours ago
by Sunil vignesh
Not Answered
Cmake Errors while building code in nrf5340dk 0

when I try to build a code for integrating sensor in nRF 5340 dk, this error comes, I tried even after installing cmake manually from the cmake website https://cmake.org/...
- development
- code
- Evaluation
- configuration
- zephyr
- nRF5340
31 views

0 replies

Started 19 hours ago
by Gouri
Not Answered
Understanding "S1-U data transfer: Not supported" with nRF9160 on Private NB-IoT (Network Owner Claims Modem Origin) 0

Hello, I am using an nRF9160 to connect to a private network. My nRF9160 successfully attaches to this network. However, when reviewing the logs from the private network...
67 views

0 replies

Started 1 day ago
by l0cszp
Not Answered
nRF54L15 continuous wave mode 0

Hello, How can I put the nRF54L15 into continuous wave mode? And I assume after entering CW that I can freely change channels using the FREQUENCY register (0x708). Is that...
42 views

0 replies

Started 1 day ago
by kitc22
Not Answered
Adding Actinius Icarus nRF9160 as LTE device in nRF cloud 0

Hi, I'm currently trying to add an Actinius Icarus IoT board as LTE device at nRF cloud. I already know my board IMEI (I got it by flashing the AT client sample and then...
37 views

0 replies

Started 1 day ago
by Rocio Cabral

Recent in Nordic blog

nRF52 Range Extension with RFaxis' RFX2411N

Floyd Ashbaugh

External Power Amplifiers and LNAs easily connected to the nRF52 series device for high power extended range operation. Data sheets, white papers, schematics and layout information available at link t…
- 26 Jan 2016
Developing Nordic nRF51 applications with mbed and Visual Studio

ivan

This tutorial shows how to use the mbed framework to develop applications for Nordic nRF51 devices. Before you begin, install VisualGDB 5.1 or later. Start Visual Studio and open the VisualGDB Embedded…
- 26 Jan 2016
PA / LNA support in S132

Einar Thorsrud

The S132 SoftDevice for the nRF52 has support for enable/disable switching of external Power Amplifiers (PA) and Low Noise Amplifiers (LNA) using GPIO pins. This was introduced in S132 version 2.0.0-7…
- 25 Jan 2016
Step by Step Guide to Setup and Start Developemt with nRF51 or nRF52 DK and IAR

Pratyush Dave

The purpose of this blog is to provide a step by step guide to help a developer, starting off with the Nordic Semiconductor nRF51 DK, to get the necessary tools installed and get the software (SW) development…
- 25 Jan 2016
BLE nrf51 - Multilink NUS central - Connect to many peripherals through NUS service - with Arduino host

Marco Russi

Hi all, I implemented a simple multilink NUS central based on s130 for nrf51 chip-set. It means that this NUS central can connect to several peripherals simultaneously and send data to each one of them…
- 24 Jan 2016
SEGGER Embedded Studio Part 2 - Monitor Mode Debugging

Michael Dietz

This tutorial will take less than 15 minutes. #Motivation Never lose a BLE connection when debugging your applications again! This technique will also be useful for any application using the PWM peripheral…
- 22 Jan 2016