Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
nRF Connect for Desktop advertising restart after disconnect 0

Hi After each connection, I should press Alt-A. Is it possible to add a feature so the advertising will restart automatically after the connection is finished?
519 views

0 replies

Started over 2 years ago
by Mike Tuev R9FT
Not Answered
case about nRF9160 program modem 0

none
524 views

0 replies

Started over 2 years ago
by peter.min
Not Answered
nRF5 SDK 17.1.0 systeminit for nRF52840 and TRACE data 0

Hello Support Team! I use nRF52840 and migrate to nRF5 SDK 17.1.0. But I can't use Trace functionality, because SystemInit method from system_nrf52.c file use wrong pins...
931 views

0 replies

Started over 2 years ago
by kchuva
Not Answered
ncs v2.0.0 basic peripheral_lbs custom board sample 0

please delete
548 views

0 replies

Started over 2 years ago
by billywalton
Not Answered
Periodic Advertising nRF Connect SDK 0

Kindly close the ticket, I'm unable to delete it. The issue got resolved.
584 views

0 replies

Started over 2 years ago
by Sukriti

Recent in Nordic blog

Developing Nordic nRF51 Projects with Visual Studio

ivan

This tutorial shows how to create and debug a basic project for the Nordic nRF51-DK using Visual Studio. Before you begin, install VisualGDB 5.0 or later. Start Visual Studio and begin creating a new…
- 6 Aug 2015
Motor Control over BLE with nRF51822 and TB6612FNG

Mahesh Venkitachalam

In this project, we will control two motors over BLE using the Nordic nRF51-DK. To do this, we will use a motor driver based on the Toshiba TB6612FNG chip. We will use GPIOs and PWM to communicate with…
- 5 Aug 2015
Create Hurricane Tunnel Broker on Raspberry Pi

Eugene Yu

This blog introduces how to create tunnel broker service in order to support IPv6 on your IPv4 network. The tunnel broker is providing IP conversion service with 6in4. Preparation Raspberry Pi…
- 4 Aug 2015

Latest guides

Peripherals And RF Test: Adding a Peripheral(SPI) to an NCS (version 1.x) Zephyr project

Jeff4BLE

Objectives Provide a brief primer to NCS and Zephyr Provide a quick-start guide to adding peripherals to an existing sample project Demonstrate running both foreground and background tasks within Zephyr…
- 21 Feb 2021
Getting started: How to add DFU support to your Thingy:91 project

Didrik Rokhaug

Note: From nRF Connect SDK v1.7.0 onwards, if you build for the thingy91_nrf9160_ns or thingy91_nrf52840, everything in this guide is already done automatically. Since that SDK release, the board files…
- 21 Jan 2021
Software: Enter the Multi-NUS: A Simple Wireless UART Network

matt.heins

If you’re thinking about building a network of sensors and you begin to survey the options, you’re likely to encounter a frothing sea of acronyms representing a variety of standards and protocols clamoring…
- 12 Jan 2021
Software and Protocols: nRF9160 DK: Offloading Bluetooth Low Energy related tasks to nRF52840 SoC

Anders Storro

Background Some time ago I was working on a project that involved communication between Bluetooth mesh and a home automation platform. The goal of this project was to enable control and observability of…
- 12 Jan 2021
Bluetooth low energy: How to update advertising data dynamically using BLE Advertising library

Karl Ylvisaker

Introduction The question of how to update advertising data dynamically using the BLE Advertising library has been raised many times by our forum-goers, especially after the release of nRF5 SDK v15.2.0…
- 6 Jan 2021
Software: Device Firmware Update (DFU) with MCUBoot bootloader

Mark Q

Purpose The purpose of this blog is to show how to create a Zephyr application that boots from the MCUBoot bootloader. We will also show how to update an application using the Device Firmware Update (DFU…
- 3 Nov 2020