Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
nRF51822 books, documentation 0

Hello. Can I get a literature to the nRF51 series? I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
- bluetooth low energy
- nrf51822
875 views

0 replies

Started over 9 years ago
by HAKMUN
Not Answered
some connect problem when use hts . 0

hts, HTC phone, nrf tools HTM, nrf51822, every time when it's power up : the once connect: error code 0x7A cann't read characteristic and 0x14 state change. the second...
- hts err manual
703 views

0 replies

Started over 9 years ago
by Liu
Not Answered
4 channel wireless transceiver and 4 RF temperature sensors as a finished product set: 0

Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
- any fcc approved
1061 views

0 replies

Started over 9 years ago
by baha93
Not Answered
How to get Value of multilink_peripheral on terminal, that is displayed on Mastrer Control panel 0

I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
- value
- mcp
- dongle
- lave
- terminal
627 views

0 replies

Started over 9 years ago
by Mohib
Not Answered
SPI Multiple Masters 0

Hello, I am tryong to use to masters to communicate with two accelerometers. Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
- spi
- multiple master and slave
2612 views

0 replies

Started over 9 years ago
by Milad

Recent in Nordic blog

Motor Control over BLE with nRF51822 and TB6612FNG

Mahesh Venkitachalam

In this project, we will control two motors over BLE using the Nordic nRF51-DK. To do this, we will use a motor driver based on the Toshiba TB6612FNG chip. We will use GPIOs and PWM to communicate with…
- 5 Aug 2015
Create Hurricane Tunnel Broker on Raspberry Pi

Eugene Yu

This blog introduces how to create tunnel broker service in order to support IPv6 on your IPv4 network. The tunnel broker is providing IP conversion service with 6in4. Preparation Raspberry Pi…
- 4 Aug 2015
An appeal to makers - why you should document your project, and how you can do it

Mahesh Venkitachalam

An appeal to makers - why you should document your project, and how you can do it. http://electronut.in/why-how-document-project/
- 3 Aug 2015

Latest guides

Getting Started: Developing for the nRF52805 with nRF5 SDK

bjorn-spockeli

Introduction The nRF52805 SoC is a low-cost member of the nRF52 Series with a subset of the features of the nRF52811 and nRF52810 SoCs. As the nRF52805 has a feature subset of the nRF52810/11 SoCs, which…
- 11 Jun 2020
nRF5x: nRF52832 Specific PCB Guidelines

Andreas

This guide will cover the specific areas that must be paid extra attention to when designing a PCB for nRF52832. It is intended as a nRF52832 specific addition to the General PCB design guidelines for…
- 10 Jun 2020
Hardware design, RF test and coverage: iBasis eSIM International Coverage Update

Brian Kim

Since Nordic Semiconductor announced that it has partnered with one of the world’s largest international cellular carriers, iBASIS, to use nRF9160 System-in-Package (SiP) module and to include an iBasis…
- 4 Jun 2020
Getting started: Getting NB-IoT Demo running on Thingy:91

Christian Kurz

The Nordic Thingy:91 is a cellular IoT prototyping platform. It is based on the nRF9160 System-in-Package (SiP). The nRF9160 has an integrated modem that supports both LTE-M and NB-IoT. The factory programmed…
- 29 May 2020
Bluetooth low energy: Mocking CoreBluetooth

Aleksander Nowakowski

CoreBluetooth is the native iOS framework to communicate with Bluetooth-enabled Low Power (LE) devices, except iBeacons (which require CoreLocation) and HomeKit devices. It is easy to start with, if one…
- 9 Mar 2020
Getting Started : Build NCS application firmware images using Docker

Markus Tacker (he/him)

How to compile a NCS application using Docker so you don't need to install dependencies directly in your system.
- 17 Feb 2020