Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Unable to check anything on hyperterminal or teraterm. How to check it? 0

Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
743 views

0 replies

Started over 9 years ago
by Hamza
Not Answered

nrf905 Data loss 0

Hi,my friend, Now,I use nrf905.Situation is as follows: I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data. 1.The Product host is to use the stick...

494 views

0 replies

Started over 9 years ago
by Jesen
Not Answered
RedBear Blend Micro use pairing passkey 0

Hi, I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device. Is it possible? Static passkey...
- ble blend passkey io
734 views

0 replies

Started over 9 years ago
by isi
Not Answered
How to interface multiple RF transmitters with single RF reciever? 0

How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ? I am working on a polling system. This one is similar to the audience...
- 433mhz
2302 views

0 replies

Started over 9 years ago
by Ajinkya
Not Answered
Writing peripheral characteristic value 0

Hello, I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
- value
- bluetooth low energy
- keil
- write
- nrf51822
- characteristic
2581 views

0 replies

Started over 9 years ago
by nejcokle

Recent in Nordic blog

Step by Step Guide to Setup and Start Developemt with nRF51 or nRF52 DK and IAR

Pratyush Dave

The purpose of this blog is to provide a step by step guide to help a developer, starting off with the Nordic Semiconductor nRF51 DK, to get the necessary tools installed and get the software (SW) development…
- 25 Jan 2016
BLE nrf51 - Multilink NUS central - Connect to many peripherals through NUS service - with Arduino host

Marco Russi

Hi all, I implemented a simple multilink NUS central based on s130 for nrf51 chip-set. It means that this NUS central can connect to several peripherals simultaneously and send data to each one of them…
- 24 Jan 2016
SEGGER Embedded Studio Part 2 - Monitor Mode Debugging

Michael Dietz

This tutorial will take less than 15 minutes. #Motivation Never lose a BLE connection when debugging your applications again! This technique will also be useful for any application using the PWM peripheral…
- 22 Jan 2016

Latest guides

Getting started: How to add DFU support to your Thingy:91 project

Didrik Rokhaug

Note: From nRF Connect SDK v1.7.0 onwards, if you build for the thingy91_nrf9160_ns or thingy91_nrf52840, everything in this guide is already done automatically. Since that SDK release, the board files…
- 21 Jan 2021
Software: Enter the Multi-NUS: A Simple Wireless UART Network

matt.heins

If you’re thinking about building a network of sensors and you begin to survey the options, you’re likely to encounter a frothing sea of acronyms representing a variety of standards and protocols clamoring…
- 12 Jan 2021
Software and Protocols: nRF9160 DK: Offloading Bluetooth Low Energy related tasks to nRF52840 SoC

Anders Storro

Background Some time ago I was working on a project that involved communication between Bluetooth mesh and a home automation platform. The goal of this project was to enable control and observability of…
- 12 Jan 2021
Bluetooth low energy: How to update advertising data dynamically using BLE Advertising library

Karl Ylvisaker

Introduction The question of how to update advertising data dynamically using the BLE Advertising library has been raised many times by our forum-goers, especially after the release of nRF5 SDK v15.2.0…
- 6 Jan 2021
Software: Device Firmware Update (DFU) with MCUBoot bootloader

Mark Q

Purpose The purpose of this blog is to show how to create a Zephyr application that boots from the MCUBoot bootloader. We will also show how to update an application using the Device Firmware Update (DFU…
- 3 Nov 2020
Software: Building a Bluetooth application on nRF Connect SDK- Comparing and contrasting to SoftDevice based applications - Part 1

Hung Bui

Scope This is a discussion on building a Bluetooth application on our new nRF Connect SDK/Zephyr platform with the reflections to our nRF5 SDK which is based on the SoftDevice Bluetooth stack. The goal is…
- 21 Oct 2020