Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
GPIOTE port event and pin events enable issue simultaneously 0

hi all , how to enable GPIOTE PORT and IN[n] event simultaneously ?(not same pin) i enable the GPIOTE to trigger interrupt event. one for the keyboard which need multiple...
- gpiote
- nrf51822
1774 views

0 replies

Started over 10 years ago
by steven
Not Answered
Cycle speed and cadence sensor data , even after stopping the cycle ? 0

Hi All, I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem. ...
- nrf51422
- ant
733 views

0 replies

Started over 10 years ago
by Robin
Not Answered

Write and read back the FSR register failed 0

Hello Nordic Team, I have a problem with programming the nRF24LE1 chip. I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...

929 views

0 replies

Started over 10 years ago
by MasterAlexei
Not Answered
SDK 6.0.0 OTA DFU iOS compatibility 0

Hi, I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
- s110
- bootloader
- jlink
- keil
- dfu
- nrf51822
1363 views

0 replies

Started over 10 years ago
by Florin
Not Answered
GATT database for a server 0

I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
- gatt nrf51822
- bluetooth low energy
1545 views

0 replies

Started over 10 years ago
by kb

Recent in Nordic blog

Programming the nRF51822 Beacon Kit with the nRF51DK

Stefan Birnir Sverrisson

One way to program the nRF51822 Bluetooth Smart Beacon Kit is to use the nRF51 DK. This gives you a full scale development platform (the nRF51 DK). This blog will go thru the steps needed to program…
- 7 May 2015
Bluz, a cloud connected Bluetooth LE development kit based on the nRF51822, is live on Kickstarter

eric ely

Bluz is a brand new development kit that brings Bluetooth LE to the internet. We have paired up with Spark and ported their FW to the nrf51822, allowing Bluz to be controlled and programmed over the…
- 15 Apr 2015
nRF51 current consumption for common scenarios

Stefan Birnir Sverrisson

The following is the estimated nRF51 current consumption during advertising with the DCDC disabled. Advertising 1: TX power: +4dBm adv interval: 20ms (minimum advertising interval in normal adversising…
- 14 Apr 2015
Building kernel for RPi2 with bluetooth_6lowpan for Raspbian

Håkon Alseth

Building kernel for RPi2 with bluetooth_6lowpan In this guide, you will have two choices: Cross-compilation build Native build Choose the one that fits your needs. Cross-compilation is…
- 9 Apr 2015
Debugging with Real Time Terminal

FormerMember

In SDK 12.0.0 or later, logging/debugging over RTT is built in to the logger module NRF_LOG. To enable logging over RTT, "check" the NRF_LOG_BACKEND_SERIAL_USES_RTT option in sdk_config.h in the configuration…
- 8 Apr 2015
Accessing the BLE mesh via the particle.io (spark.io) cloud

David Edwin

Hello. I was spending the last few days to implement an interface to access the BLE mesh via the Internet. The mesh consists of devices with LEDs, which then could be turned on and off in my browser.…
- 1 Apr 2015