Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
S310 radio hardware 0

Hello, can the radio notification and radio disable APIs be used to use the radio hardware from the application layer? Background of my question is, that I have an application...
632 views

0 replies

Started over 10 years ago
by Torsten Robitzki
Not Answered
Retrieve the peripheral name advertised when connection has been done 0

Hi, I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral. When connection is done, the...
- 120 s110 nrf51822
805 views

0 replies

Started over 10 years ago
by Sébastien Despont
Not Answered

AES ENCRYPTATION with sd_ecb_block_encrypt in nRF51822 BLUETOOTH SMART BEACON KIT 0

Hello, I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device. I used this code to ecrypt the data ( this is...

1324 views

0 replies

Started over 10 years ago
by Ivan Gómez
Not Answered
nRF UART App error 0

Hi, i use anRF51822 with soft device 7. I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5. Both devices connected...
- s110
- bluetooth low energy
- uart
- keil
- nrf51822
- nordic
1727 views

0 replies

Started over 10 years ago
by max
Not Answered
nRFgo Studio will not launch after upgrading to 1.17.0 0

Hello, I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
- nrf51822 nrfgo
953 views

0 replies

Started over 10 years ago
by Archie

Recent in Nordic blog

Developing Nordic nRF51 applications with mbed and Visual Studio

ivan

This tutorial shows how to use the mbed framework to develop applications for Nordic nRF51 devices. Before you begin, install VisualGDB 5.1 or later. Start Visual Studio and open the VisualGDB Embedded…
- 26 Jan 2016
PA / LNA support in S132

Einar Thorsrud

The S132 SoftDevice for the nRF52 has support for enable/disable switching of external Power Amplifiers (PA) and Low Noise Amplifiers (LNA) using GPIO pins. This was introduced in S132 version 2.0.0-7…
- 25 Jan 2016
Step by Step Guide to Setup and Start Developemt with nRF51 or nRF52 DK and IAR

Pratyush Dave

The purpose of this blog is to provide a step by step guide to help a developer, starting off with the Nordic Semiconductor nRF51 DK, to get the necessary tools installed and get the software (SW) development…
- 25 Jan 2016
BLE nrf51 - Multilink NUS central - Connect to many peripherals through NUS service - with Arduino host

Marco Russi

Hi all, I implemented a simple multilink NUS central based on s130 for nrf51 chip-set. It means that this NUS central can connect to several peripherals simultaneously and send data to each one of them…
- 24 Jan 2016
SEGGER Embedded Studio Part 2 - Monitor Mode Debugging

Michael Dietz

This tutorial will take less than 15 minutes. #Motivation Never lose a BLE connection when debugging your applications again! This technique will also be useful for any application using the PWM peripheral…
- 22 Jan 2016
An introduction to error handling in nRF5 projects

Audun

As you start developing with the nRF5 series chips, SoftDevices, and SDKs, it's very useful to learn how errors can be discovered (and preferrably recovered from). This can be detecting something as simple…
- 20 Jan 2016