Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
StartServiceDiscovery fails after disconnection (VS10, C#) 0

After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again. IsDeviceDiscoveryOngoing was checked before. The...
- masteremulator
- mcp
- c#
997 views

0 replies

Started over 10 years ago
by Damien
Not Answered

Processing/debugging received data in PCA10000 0

Hi, I wanted to ask a question regarding sending data. I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...

491 views

0 replies

Started over 10 years ago
by john
Not Answered

nRF51822 communicate with nRF2401E 0

Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...

572 views

0 replies

Started over 10 years ago
by flyinggirlxhx
Not Answered
When SLAVE_LATENCY not equal to zero, connect will disconnect sometime. 0

E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard SDK 6.0.0 Softdevice 7.0 When I connect to Android 4.4.3 device(Nexus7 II) will...
- s110
- nrf51822
1029 views

0 replies

Started over 10 years ago
by gootoomoon
Not Answered
when I set SLAVE_LATENCY = 3 or other none zero number,ble connect will disconnect auto 0

E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard SDK 6.0.0 Softdevice 7.0 When I connect to Android 4.4.3 device(Nexus7 II) will...
- s110
- softdevice 7.0
- nrf51822
- sdk 6.0
770 views

0 replies

Started over 10 years ago
by gootoomoon

Recent in Nordic blog

nRF52840-DK Range Testing With BLE, ZigBee and Thread Protocols at 0, 4 and 8dBm Transmit Power Settings

notsane0

Range testing of any RF scheme is inherently limited by the RF environment, antenna design, tuning and many other factors. The usefulness of range testing is to provide a basis for comparison while keeping…
- 28 Dec 2018
Thingy:52 MOSFET Usage

gamnes

This blog post describes how you can take advantage of the 4 MOSFET's on the Thingy:52. DISCLAIMER: Please verify all information that is used/retrieved from this blog post. Some of the information…
- 27 Dec 2018
Using the Power Profiling Kit to measure Current Draw on an External Device

notsane0

The Power Profiler Kit (PPK) is a flexible tool for measuring the real-time current draw of nRF5x designs. When used as an add-on board to measure the nRF5x current of an attached development kit (DK)…
- 26 Dec 2018

Latest guides

Getting Started: Developing for the nRF52805 with nRF5 SDK

bjorn-spockeli

Introduction The nRF52805 SoC is a low-cost member of the nRF52 Series with a subset of the features of the nRF52811 and nRF52810 SoCs. As the nRF52805 has a feature subset of the nRF52810/11 SoCs, which…
- 11 Jun 2020
nRF5x: nRF52832 Specific PCB Guidelines

Andreas

This guide will cover the specific areas that must be paid extra attention to when designing a PCB for nRF52832. It is intended as a nRF52832 specific addition to the General PCB design guidelines for…
- 10 Jun 2020
Hardware design, RF test and coverage: iBasis eSIM International Coverage Update

Brian Kim

Since Nordic Semiconductor announced that it has partnered with one of the world’s largest international cellular carriers, iBASIS, to use nRF9160 System-in-Package (SiP) module and to include an iBasis…
- 4 Jun 2020
Getting started: Getting NB-IoT Demo running on Thingy:91

Christian Kurz

The Nordic Thingy:91 is a cellular IoT prototyping platform. It is based on the nRF9160 System-in-Package (SiP). The nRF9160 has an integrated modem that supports both LTE-M and NB-IoT. The factory programmed…
- 29 May 2020
Bluetooth low energy: Mocking CoreBluetooth

Aleksander Nowakowski

CoreBluetooth is the native iOS framework to communicate with Bluetooth-enabled Low Power (LE) devices, except iBeacons (which require CoreLocation) and HomeKit devices. It is easy to start with, if one…
- 9 Mar 2020
Getting Started : Build NCS application firmware images using Docker

Markus Tacker (he/him)

How to compile a NCS application using Docker so you don't need to install dependencies directly in your system.
- 17 Feb 2020