Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered

Logging UART data on a PC 0

Hello, I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop. I have two questions: ...

1533 views

0 replies

Started over 12 years ago
by Aditya Bansal
Not Answered
Which priority does softdevice set for SWI2_IRQn 0

SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them? Does sd_nvic_critical_region_enter() disable...
- interrupts
1474 views

0 replies

Started over 12 years ago
by cnshibo
Not Answered
What is the way to have a simple BLE chip work? 0

I am a started guy. I only need a bluetooth device (BLE) to check the signal and mac address. What is the best choice? I need the smallest and low powered! Thank you...
- power
- address
1126 views

0 replies

Started over 12 years ago
by Pedro Lopes
Not Answered

sd_power_system_off goes directly to main() in sdk5.2 0

nrf_gpio_cfg_sense_input(IO_PORT_INT_BUTTON, GPIO_PIN_CNF_PULL_Disabled, GPIO_PIN_CNF_SENSE_Low); APP_ERROR_CHECK(sd_power_system_off()); after sd_power_system_off...

1200 views

0 replies

Started over 12 years ago
by julian
Not Answered
Bonds/pStorage with fast connection interval 0

I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
- ancs
- pstorage
- timing
- softdevice
- bond manager
1086 views

0 replies

Started over 12 years ago
by Eric Salem

Recent in the DevZone Blog

The S132 v5.1.0 is now production tested on nRF52810

Petter Myhre

This blog describes how you can setup a Segger Embedded Studio example for PCA10040E (emulating nRF52810) from nRF5 SDK 14.2 to use S132 v5.1.0, instead of S112. The procedure should be similar for the…
- 12 Sep 2018
Adding custom commands to a BLE example using Nordic UART Service

Håvard

A common thing to do is to use the Nordic UART Service for quick prototyping. Often the example itself is used as a starting point (ble_app_uart). But sometimes we use other starting points, and want to…
- 6 Sep 2018
Using Two-Factor Authentication (2FA) with the Nordic DevZone

esivertsen

Did you know you can use two-factor authentication to enhance the security of your DevZone account? In this little blog, I’ll show you how to enable Two-Factor Authentication (2FA) with your DevZone account…
- 30 Aug 2018
Introduction of SDH and SDK v15.0 software architecture

Amos Lin

The SDK software architecture has been hugely changed since SDK v13.0. With adding SDH to SDK, it provides SDH API to Enabling the SoftDevice and its event interrupt. Disabling the SoftDevice. Receiving…
- 13 Aug 2018
Bluetooth pairing vulnerability

PaKa

The Bluetooth SIG released an errata for the 4.2 and 5.0 versions of Bluetooth specification on July 23rd relating to a potential vulnerability with the pairing procedures. For Bluetooth low energy; this…
- 27 Jul 2018
Getting Started with the Thingy:52 and GCC/GDB

Daniel Veilleux

The Thingy:52 IoT Sensor Kit is a fancy development board that combines the nRF52832 SoC, a handful of sensors and user interface components, and a rechargeable battery. Although the Thingy is available…
- 20 Jul 2018