Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered

nRF24L01+ transmitting before auto acknowledgement is complete. 0

I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...

1662 views

0 replies

Started over 10 years ago
by David Watson
Not Answered
Connect another board over UART from nRF51822 mKit board 0

I am using mbed library to get leg up on development. This is the first time I am writing any MCU application and it sure makes things a lot easier. I am using nRF51822...
- mbed
- uart
- nrf51822
1414 views

0 replies

Started over 10 years ago
by Jigar Patel
Not Answered
HID Service on iOS 0

I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
1959 views

0 replies

Started over 10 years ago
by Adam
Not Answered

the speed of large amount of data 0

int main(void) { uint32_t BufferCount; uint32_t err_code; // Initialize leds_init(); timers_init(); buttons_init(); uart_init(); ble_stack_init(); gap_params_init...

948 views

0 replies

Started over 10 years ago
by fitfuel
Not Answered
Gazell library source code. 0

Hi I have a question about using gazell link layer and paring library with concurrent timeslot api. I try to do this but i have the hard fault handler after invoked nrf_gzll_init...
- gazell
- nrf51822
1498 views

0 replies

Started over 10 years ago
by Firek

Recent in Nordic blog

6LoWPAN for Bluetooth low energy on OpenWRT

Glenn Ruben Bakke

OpenWRT is one of the most popular open source Linux-based router firmware alternatives for commodity routers. From kernel 3.17, Linux has supported 6LoWPAN for Bluetooth low energy (BLE) through the…
- 13 Mar 2015
IPv6-Brewed Coffee Over Bluetooth Smart

Glenn Ruben Bakke

Believe it or not, the day has come when your coffee machine could know what exactly what kind of coffee you like to drink depending on the cup you’re using, the time of day, and a multitude of other…
- 4 Mar 2015
Debugging Arduino project with Atmel Studio

Stefan Birnir Sverrisson

When using nRF8001 with an Arduino board, Atmel Studio is a good free tool to use for development of your firmware. The following video shows a procedure in Atmel Studio in order to enable debugging of…
- 19 Feb 2015

Latest guides

Software and Protocols: Automating nRF91 TLS credential management via serial port AT commands

Daniel Veilleux

I have spent a bit of time recently experimenting with different TLS credential configurations using nRF91-DKs. Eventually I got to the point where I wanted to do things like swap out the certificates…
- 10 Jan 2020
Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019