Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered

Which mode can use to set up a dynamic network? 0

Hi, Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...

613 views

0 replies

Started over 10 years ago
by mahone
Not Answered

nRF24AP2 Rx behaviour 0

Dir Sir. I am checking the current profile of nRF24AP2 in RX mode. After "open channel" command, I found the peak current at 10ms interval until connection pass. How does...

796 views

0 replies

Started over 10 years ago
by kazuo KATO
Not Answered

Logging UART data on a PC 0

Hello, I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop. I have two questions: ...

1306 views

0 replies

Started over 10 years ago
by Aditya Bansal
Not Answered
Which priority does softdevice set for SWI2_IRQn 0

SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them? Does sd_nvic_critical_region_enter() disable...
- interrupts
1261 views

0 replies

Started over 10 years ago
by cnshibo
Not Answered
What is the way to have a simple BLE chip work? 0

I am a started guy. I only need a bluetooth device (BLE) to check the signal and mac address. What is the best choice? I need the smallest and low powered! Thank you...
- power
- address
888 views

0 replies

Started over 10 years ago
by Pedro Lopes

Recent in Nordic blog

Thingy:52 MOSFET Usage

gamnes

This blog post describes how you can take advantage of the 4 MOSFET's on the Thingy:52. DISCLAIMER: Please verify all information that is used/retrieved from this blog post. Some of the information…
- 27 Dec 2018
Using the Power Profiling Kit to measure Current Draw on an External Device

notsane0

The Power Profiler Kit (PPK) is a flexible tool for measuring the real-time current draw of nRF5x designs. When used as an add-on board to measure the nRF5x current of an attached development kit (DK)…
- 26 Dec 2018
What impact does the deprecation and withdrawal of Bluetooth Core specification v4.0 and v4.1 have on your current and future products?

Petter Myhre

This blog was last updated 17.01.2019. The Bluetooth Special Interest Group (SIG) recently announced the deprecation and withdrawal of Bluetooth Core specifications v4.0 and v4.1. For products that are…
- 30 Oct 2018

Latest guides

Bluetooth low energy: Wireless timer synchronization among nRF5 devices

Audun

Introduction In a variety of use cases there is a need to share a common clock among multiple devices. Such a common clock can be used for many purposes, for example by having each node in a network perform…
- 12 Jul 2016
nRF5x: General PCB design guidelines for nRF52 series

FormerMember

When designing a PCB with a high-frequency radio onboard certain rules should be followed for optimal radio frequency (RF) performance. This guide will provide some general PCB guidelines that can be used…
- 11 Jul 2016
Software Development Kit: Migrating to Peer Manager

Øyvind Rønningstad

The tutorial has been updated for SDK v11, which contains the production-ready release of Peer Manager. The original tutorial can be found on this page, below the updated tutorial. #Migrating to Peer…
- 8 Apr 2016
Bluetooth low energy: Bluetooth low energy Characteristics, a beginner's tutorial

MartinBL

Before we begin Table of content Topics that will be covered include: Before we begin Basic theory Attribute tables in nRFConnect Bluetooth Low Energy application Description of the example Adding a…
- 18 Mar 2016
Bluetooth low energy: Bluetooth Smart and the Nordic's Softdevices - Part 2 Connection

Hung Bui

This blog series was created as an attempt to fill in the gap between how Bluetooth Smart is described in the spec and how you can use our APIs and event from our softdevice to do what defined in the spec…
- 1 Feb 2016
Design Examples: Capacitive Touch on the nRF52 series

Einar Thorsrud

Important updates: Due to erratum 84 (COMP: ISOURCE not functional), capacitive sensing using the relaxation oscillator method is not usable in a real product with the nRF52832, as it will only work reliably…
- 31 Jan 2016