Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered

nRF24AP2 Rx behaviour
View Voters Login to vote on this thread 0 Login to vote on this thread
0

Dir Sir. I am checking the current profile of nRF24AP2 in RX mode. After "open channel" command, I found the peak current at 10ms interval until connection pass. How does...

799 views

0 replies

Started over 10 years ago
by kazuo KATO
Not Answered

Logging UART data on a PC
View Voters Login to vote on this thread 0 Login to vote on this thread
0

Hello, I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop. I have two questions: ...

1310 views

0 replies

Started over 10 years ago
by Aditya Bansal
Not Answered
Which priority does softdevice set for SWI2_IRQn
View Voters Login to vote on this thread 0 Login to vote on this thread
0

SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them? Does sd_nvic_critical_region_enter() disable...
- interrupts
1265 views

0 replies

Started over 10 years ago
by cnshibo
Not Answered
What is the way to have a simple BLE chip work?
View Voters Login to vote on this thread 0 Login to vote on this thread
0

I am a started guy. I only need a bluetooth device (BLE) to check the signal and mac address. What is the best choice? I need the smallest and low powered! Thank you...
- power
- address
892 views

0 replies

Started over 10 years ago
by Pedro Lopes
Not Answered

sd_power_system_off goes directly to main() in sdk5.2
View Voters Login to vote on this thread 0 Login to vote on this thread
0

nrf_gpio_cfg_sense_input(IO_PORT_INT_BUTTON, GPIO_PIN_CNF_PULL_Disabled, GPIO_PIN_CNF_SENSE_Low); APP_ERROR_CHECK(sd_power_system_off()); after sd_power_system_off...

1039 views

0 replies

Started over 10 years ago
by julian

Recent in Nordic blog

Thingy:52 MOSFET Usage

gamnes

This blog post describes how you can take advantage of the 4 MOSFET's on the Thingy:52. DISCLAIMER: Please verify all information that is used/retrieved from this blog post. Some of the information…
- 27 Dec 2018
Using the Power Profiling Kit to measure Current Draw on an External Device

notsane0

The Power Profiler Kit (PPK) is a flexible tool for measuring the real-time current draw of nRF5x designs. When used as an add-on board to measure the nRF5x current of an attached development kit (DK)…
- 26 Dec 2018
What impact does the deprecation and withdrawal of Bluetooth Core specification v4.0 and v4.1 have on your current and future products?

Petter Myhre

This blog was last updated 17.01.2019. The Bluetooth Special Interest Group (SIG) recently announced the deprecation and withdrawal of Bluetooth Core specifications v4.0 and v4.1. For products that are…
- 30 Oct 2018

Latest guides

Software and Protocols: How to connect nRF9160 DK to Google Cloud

Marte Myrvold

This project was originally made in an outdated version of NCS, but it has now been updated to NCS v1.5.0. The instructions are the same as before, but the code is different. Disclaimer: This is a student…
- 17 Jul 2019
Mesh Networks: Automating Nordic BLE Mesh Provisioning

Mark Q

Purpose This document will show how to automate the provisioning process for Nordic BLE Mesh nodes using Python scripting. When provisioning nodes using PyACI (Python Application Controller Interface)…
- 8 Jul 2019
Bluetooth low energy: MIDI over Bluetooth LE

Håvard

I implemented parts of the BLE-MIDI service along with a small example application. I wanted to share it here on the blog, in case someone would find it useful. The intended audience is primarily someone…
- 30 Jun 2019
Mesh Networks: Thread Tutorial: Practical guide for device upgrade OTA

AndreasF

This getting started guide is meant as a more detailed practical guide for the Thread Secure DFU Example found on Infocenter which demonstrates upgrade of firmware over the air (OTA). For any questions…
- 7 Jun 2019
Mesh Networks: Zigbee Tutorial: Practical guide for device upgrade OTA

AndreasF

This getting started guide is meant as a more detailed practical guide for the Zigbee OTA (Over the Air) Upgrade Client Example found on Infocenter. If you have any questions regarding Zigbee or Zigbee…
- 27 May 2019
Getting Started : nRF Connect SDK Tutorial series - Part 0 | NCS v1.5.0

Simon

This tutorial uses an outdated version of nRF Connect SDK. We recommend using the latest version of nRF Connect SDK when getting started with development. Please see academy…
- 24 May 2019

Nordic DevZone

nRF24AP2 Rx behaviour View Voters Login to vote on this thread 0 Login to vote on this thread 0

Logging UART data on a PC View Voters Login to vote on this thread 0 Login to vote on this thread 0

Which priority does softdevice set for SWI2_IRQn View Voters Login to vote on this thread 0 Login to vote on this thread 0

What is the way to have a simple BLE chip work? View Voters Login to vote on this thread 0 Login to vote on this thread 0

sd_power_system_off goes directly to main() in sdk5.2 View Voters Login to vote on this thread 0 Login to vote on this thread 0

nRF24AP2 Rx behaviour
View Voters Login to vote on this thread 0 Login to vote on this thread
0

Logging UART data on a PC
View Voters Login to vote on this thread 0 Login to vote on this thread
0

Which priority does softdevice set for SWI2_IRQn
View Voters Login to vote on this thread 0 Login to vote on this thread
0

What is the way to have a simple BLE chip work?
View Voters Login to vote on this thread 0 Login to vote on this thread
0

sd_power_system_off goes directly to main() in sdk5.2
View Voters Login to vote on this thread 0 Login to vote on this thread
0