Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered

Which mode can use to set up a dynamic network? 0

Hi, Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...

618 views

0 replies

Started over 10 years ago
by mahone
Not Answered

nRF24AP2 Rx behaviour 0

Dir Sir. I am checking the current profile of nRF24AP2 in RX mode. After "open channel" command, I found the peak current at 10ms interval until connection pass. How does...

799 views

0 replies

Started over 10 years ago
by kazuo KATO
Not Answered

Logging UART data on a PC 0

Hello, I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop. I have two questions: ...

1310 views

0 replies

Started over 10 years ago
by Aditya Bansal
Not Answered
Which priority does softdevice set for SWI2_IRQn 0

SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them? Does sd_nvic_critical_region_enter() disable...
- interrupts
1265 views

0 replies

Started over 10 years ago
by cnshibo
Not Answered
What is the way to have a simple BLE chip work? 0

I am a started guy. I only need a bluetooth device (BLE) to check the signal and mac address. What is the best choice? I need the smallest and low powered! Thank you...
- power
- address
892 views

0 replies

Started over 10 years ago
by Pedro Lopes

Recent in Nordic blog

nRF BLINKY compatible firmware using Zephyr Bluetooth APIs

vikrant8051

Hello World !! This is simple code which is compatible for nRF Blinky App which is based on Zephyr OS Bluetooth APIs. I've tested it on #nRF52840-PDK board. Isn't it simple ? You have to just replace…
- 24 Jan 2018
How to interface a Nordic Thingy:52 using Amazon Alexa

gamnes

Interfacing the Nordic Thingy:52 from the Amazon Alexa Voice Service just had to be done! In this blog post I will briefly explain how this demo was set up, but I will direct you to the GitHub page if…
- 24 Jan 2018
Difference between nRF52840 Engineering A and B reference designs

MartinBL

After the release of nRF52840 Engineering B we have received several inquiries about the difference between Engineering A (nRF52840-QIAAAA) and Engineering B (nRF52840-QIAABB) reference designs. One reason…
- 15 Jan 2018

Latest guides

Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019
nRF5x: Automating Power Profiler Kit measurements from the command line

Daniel Veilleux

Nordic's Power Profiler Kit (PPK) is an inexpensive piece of hardware that can provide a significant amount of insight into the operation and performance of your project. Although there is a lot that…
- 2 Aug 2019