Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered

PAN item 56 TWI module lock-up problem and Rev 3 version of the chip 0

Hi, Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422? Also would you happen to have a time frame as to when the Rev 3 will...

875 views

0 replies

Started over 10 years ago
by ray
Not Answered

Why does re-connection occur 2 times？ 0

Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally. several seconds later, Open Bluetooth in the settings again, and observe the settings...

653 views

0 replies

Started over 10 years ago
by ziv
Not Answered

NRF_WDT: Not able to write to registers 0

Hi, I am trying to power off and/or disable a RR[0] with no success. I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...

1225 views

0 replies

Started over 10 years ago
by Fab
Not Answered

Limit number of packets per connection event? 0

Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...

1100 views

0 replies

Started over 10 years ago
by Paolo D
Not Answered

ANTUSB-m Dongle not working with Windows 7 0

I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...

708 views

0 replies

Started over 10 years ago
by Vamsi Talla

Recent in Nordic blog

BLE nrf51 - Multilink NUS central - Connect to many peripherals through NUS service - with Arduino host

Marco Russi

Hi all, I implemented a simple multilink NUS central based on s130 for nrf51 chip-set. It means that this NUS central can connect to several peripherals simultaneously and send data to each one of them…
- 24 Jan 2016
SEGGER Embedded Studio Part 2 - Monitor Mode Debugging

Michael Dietz

This tutorial will take less than 15 minutes. #Motivation Never lose a BLE connection when debugging your applications again! This technique will also be useful for any application using the PWM peripheral…
- 22 Jan 2016
An introduction to error handling in nRF5 projects

Audun

As you start developing with the nRF5 series chips, SoftDevices, and SDKs, it's very useful to learn how errors can be discovered (and preferrably recovered from). This can be detecting something as simple…
- 20 Jan 2016

Latest guides

Getting started: How to add DFU support to your Thingy:91 project

Didrik Rokhaug

Note: From nRF Connect SDK v1.7.0 onwards, if you build for the thingy91_nrf9160_ns or thingy91_nrf52840, everything in this guide is already done automatically. Since that SDK release, the board files…
- 21 Jan 2021
Software: Enter the Multi-NUS: A Simple Wireless UART Network

matt.heins

If you’re thinking about building a network of sensors and you begin to survey the options, you’re likely to encounter a frothing sea of acronyms representing a variety of standards and protocols clamoring…
- 12 Jan 2021
Software and Protocols: nRF9160 DK: Offloading Bluetooth Low Energy related tasks to nRF52840 SoC

Anders Storro

Background Some time ago I was working on a project that involved communication between Bluetooth mesh and a home automation platform. The goal of this project was to enable control and observability of…
- 12 Jan 2021
Bluetooth low energy: How to update advertising data dynamically using BLE Advertising library

Karl Ylvisaker

Introduction The question of how to update advertising data dynamically using the BLE Advertising library has been raised many times by our forum-goers, especially after the release of nRF5 SDK v15.2.0…
- 6 Jan 2021
Software: Device Firmware Update (DFU) with MCUBoot bootloader

Mark Q

Purpose The purpose of this blog is to show how to create a Zephyr application that boots from the MCUBoot bootloader. We will also show how to update an application using the Device Firmware Update (DFU…
- 3 Nov 2020
Software: Building a Bluetooth application on nRF Connect SDK- Comparing and contrasting to SoftDevice based applications - Part 1

Hung Bui

Scope This is a discussion on building a Bluetooth application on our new nRF Connect SDK/Zephyr platform with the reflections to our nRF5 SDK which is based on the SoftDevice Bluetooth stack. The goal is…
- 21 Oct 2020