Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered

sd_evt_get, not able to receive after sd_flash..... 0

Dear Nordic people, I am playing (6.0.0) with sd_flash_page_erase() and sd_flash_write() , seems to be working ok, Allways happens what I do expect, but I am not able to...

1060 views

0 replies

Started over 10 years ago
by Jan Krejsa
Not Answered

PAN item 56 TWI module lock-up problem and Rev 3 version of the chip 0

Hi, Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422? Also would you happen to have a time frame as to when the Rev 3 will...

877 views

0 replies

Started over 10 years ago
by ray
Not Answered

Why does re-connection occur 2 times？ 0

Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally. several seconds later, Open Bluetooth in the settings again, and observe the settings...

657 views

0 replies

Started over 10 years ago
by ziv
Not Answered

NRF_WDT: Not able to write to registers 0

Hi, I am trying to power off and/or disable a RR[0] with no success. I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...

1230 views

0 replies

Started over 10 years ago
by Fab
Not Answered

Limit number of packets per connection event? 0

Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...

1103 views

0 replies

Started over 10 years ago
by Paolo D

Recent in Nordic blog

Step by Step Guide to Setup and Start Developemt with nRF51 or nRF52 DK and IAR

Pratyush Dave

The purpose of this blog is to provide a step by step guide to help a developer, starting off with the Nordic Semiconductor nRF51 DK, to get the necessary tools installed and get the software (SW) development…
- 25 Jan 2016
BLE nrf51 - Multilink NUS central - Connect to many peripherals through NUS service - with Arduino host

Marco Russi

Hi all, I implemented a simple multilink NUS central based on s130 for nrf51 chip-set. It means that this NUS central can connect to several peripherals simultaneously and send data to each one of them…
- 24 Jan 2016
SEGGER Embedded Studio Part 2 - Monitor Mode Debugging

Michael Dietz

This tutorial will take less than 15 minutes. #Motivation Never lose a BLE connection when debugging your applications again! This technique will also be useful for any application using the PWM peripheral…
- 22 Jan 2016

Latest guides

Software: Using a custom Secure Partition Manager with your application

Heidi-Irene Harvey Sollie

One of the samples available in the nRF Connect SDK is the Secure Partition Manager, which is required to run applications in the nonsecure domain of the CPU. The sample uses the SPM library available in…
- 12 Feb 2020
Getting Started : nRF Connect SDK Bluetooth Low Energy tutorial part 1: Custom Service in Peripheral role

haakonsh

Scope The goal of this tutorial is to set-up your own custom Bluetooth Low Energy service on an nRF5340 acting in a peripheral role. We will set up a new Bluetooth LE project from scratch. The finished…
- 11 Feb 2020
Mesh Networks: Mass Provisioning of Nordic BLE Mesh Nodes

Mark Q

Purpose When creating a mesh network with many nodes, it can take a while to provision each node, especially using PyACI. An alternative is to use a static provisioner that provisions the nodes automatically…
- 8 Feb 2020
Software and Protocols: Enabling and testing TLS in mqtt_simple

Daniel Veilleux

The MQ Telemetry Transport (MQTT) protocol is hugely popular in IoT because it is lightweight and versatile. In this post we will enable Transport Layer Security (TLS) in the mqtt_simple sample from the…
- 4 Feb 2020
Getting Started: Introduction to Nordic nRF5 SDK and Softdevice

Mihua

What is the difference between SDK and Softdevice? How can we select SDK and Softdevice versions? Do the SoC, SDK, and Softdevice have version compatibility problems? How can we understand the SDK directory…
- 15 Jan 2020
Software and Protocols: Automating nRF91 TLS credential management via serial port AT commands

Daniel Veilleux

I have spent a bit of time recently experimenting with different TLS credential configurations using nRF91-DKs. Eventually I got to the point where I wanted to do things like swap out the certificates…
- 10 Jan 2020