Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
What is the way to have a simple BLE chip work? 0

I am a started guy. I only need a bluetooth device (BLE) to check the signal and mac address. What is the best choice? I need the smallest and low powered! Thank you...
- power
- address
892 views

0 replies

Started over 10 years ago
by Pedro Lopes
Not Answered

sd_power_system_off goes directly to main() in sdk5.2 0

nrf_gpio_cfg_sense_input(IO_PORT_INT_BUTTON, GPIO_PIN_CNF_PULL_Disabled, GPIO_PIN_CNF_SENSE_Low); APP_ERROR_CHECK(sd_power_system_off()); after sd_power_system_off...

1039 views

0 replies

Started over 10 years ago
by julian
Not Answered
Bonds/pStorage with fast connection interval 0

I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
- ancs
- pstorage
- timing
- softdevice
- bond manager
913 views

0 replies

Started over 10 years ago
by Eric Salem
Not Answered

SDK documentation not working on Android browsers 0

Hello, We have experienced odd problem, we are not able to scroll up or down SDK documentation at these pages on Android devices. IPHONE browser Safari works ok. Any help...

1069 views

0 replies

Started over 10 years ago
by Jan Krejsa
Not Answered

PROBLEM CAUSED BY ADDING RTC TO MY PROGRAM 0

HI,ALL！ I tried to add a RTC wakeup funtion to my ble device, so i add the code of the Nordic board example named "rtc_example" to my program. But it turned out that my...

624 views

0 replies

Started over 10 years ago
by kk

Recent in Nordic blog

Debugging on nrf52840 with GDB from CLI on linux

jfcamel

Today I tried to find the better ways to debug program on nRF52840 PDK from CLI on linux. The ways that I tried [Failed] openocd (both stlink and jlink) & gdb [Succeeded] JLink & JLinkGDBServer &…
- 14 Dec 2017
The KEY POINT of example "ble_app_uart"

QQ645116977

This article baed on "pca10040", nRF52832 example code path "examples/ble_peripheral/ble_app_uart" IMPORTANT!!!! board config file of this example located in "components/boards/pca10040.h" and uart…
- 12 Dec 2017
Introduce smart motion controller - ELIO

caram5555

"ELIO" is a Bluetooth module and smartphone application that can drive motor(DC, Servo) and illuminate LEDs. This module mounts Nordic's nRF52832 and motor controller IC. Smartphone application can create…
- 12 Dec 2017

Latest guides

Getting started: How to add DFU support to your Thingy:91 project

Didrik Rokhaug

Note: From nRF Connect SDK v1.7.0 onwards, if you build for the thingy91_nrf9160_ns or thingy91_nrf52840, everything in this guide is already done automatically. Since that SDK release, the board files…
- 21 Jan 2021
Software: Enter the Multi-NUS: A Simple Wireless UART Network

matt.heins

If you’re thinking about building a network of sensors and you begin to survey the options, you’re likely to encounter a frothing sea of acronyms representing a variety of standards and protocols clamoring…
- 12 Jan 2021
Software and Protocols: nRF9160 DK: Offloading Bluetooth Low Energy related tasks to nRF52840 SoC

Anders Storro

Background Some time ago I was working on a project that involved communication between Bluetooth mesh and a home automation platform. The goal of this project was to enable control and observability of…
- 12 Jan 2021
Bluetooth low energy: How to update advertising data dynamically using BLE Advertising library

Karl Ylvisaker

Introduction The question of how to update advertising data dynamically using the BLE Advertising library has been raised many times by our forum-goers, especially after the release of nRF5 SDK v15.2.0…
- 6 Jan 2021
Software: Device Firmware Update (DFU) with MCUBoot bootloader

Mark Q

Purpose The purpose of this blog is to show how to create a Zephyr application that boots from the MCUBoot bootloader. We will also show how to update an application using the Device Firmware Update (DFU…
- 3 Nov 2020
Software: Building a Bluetooth application on nRF Connect SDK- Comparing and contrasting to SoftDevice based applications - Part 1

Hung Bui

Scope This is a discussion on building a Bluetooth application on our new nRF Connect SDK/Zephyr platform with the reflections to our nRF5 SDK which is based on the SoftDevice Bluetooth stack. The goal is…
- 21 Oct 2020