Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered

Timeslot API - modify a radio request 0

Hi, What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session? For example,...

1052 views

0 replies

Started over 10 years ago
by Gili Elias
Not Answered
sd_ant_channel_id_set returns NRF_ERROR_INVALID_ADDR 0

Hi, I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
- nrf51422
- ant
870 views

0 replies

Started over 10 years ago
by Paul Damade
Not Answered
ANT Extended Messaging in API 0

Hi, To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
- nrf51422
- ant
- scan
822 views

0 replies

Started over 10 years ago
by Us
Not Answered

Qualification questions 0

We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...

876 views

0 replies

Started over 10 years ago
by Gus Gustafson
Not Answered
Best way to minimize NRF_ANT_ERROR_TRANSFER_IN_PROGRESS 0

What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
- softdevice
- ant
734 views

0 replies

Started over 10 years ago
by Jason De Lorme

Recent in Nordic blog

Serial Wire Debug Port Interface for nRF52832

gamnes

1.1 Description This documentation describes the use and initialization of the Serial Wire Debug Port (SWDP) interface when writing to or reading from Flash and SRAM of the nRF52832 Rev 1. See http:/…
- 2 Jun 2017
nRF52840 GATT Data Throughput with Zephyr RTOS

vich

Nordic has recently contributed support for the 2Mbit/s PHY, part of the Bluetooth 5.0 specification, to the Zephyr Project RTOS. The video below shows how to configure, build and test GATT data throughput…
- 2 Jun 2017
The complete tutorial for developing and debugging nRF52 applications on a Mac

Mohammad Afaneh

I realize that there are already multiple tutorials on how to configure GCC along with Eclipse or SEGGER Embedded Studio (for use on a Mac), but this tutorial goes over setting up a different IDE. The…
- 11 May 2017

Latest guides

Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019
nRF5x: Automating Power Profiler Kit measurements from the command line

Daniel Veilleux

Nordic's Power Profiler Kit (PPK) is an inexpensive piece of hardware that can provide a significant amount of insight into the operation and performance of your project. Although there is a lot that…
- 2 Aug 2019