Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered

Stopping app_timer (using app_timer_stop) results in too much current during ON,IDLE mode 0

I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following: Initializes the app_timer using the scheduler: ...

1578 views

0 replies

Started over 11 years ago
by Kyle
Not Answered

Control GPIO by PPI and timer1 +1

I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000. I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...

1931 views

0 replies

Started over 11 years ago
by mansfield
Not Answered

One command execution time on serialization 0

Hi, I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...

785 views

0 replies

Started over 11 years ago
by Elliot.Chao
Not Answered

Has anybody used pervasive dispalay (repaper) on NRF51822 Evaluation Kit? 0

Has anybody got it working? I ported the EPD library from Adruino EPD libray but not sure where its going wrong.

798 views

0 replies

Started over 11 years ago
by Barada Mishra
Not Answered

get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE 0

I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...

2522 views

0 replies

Started over 11 years ago
by julian

Recent in Nordic blog

Comparing compilers/IDEs for development with nRF5x series devices

Michael Dietz

#Introduction All compilers ARE NOT created equal. Given the same c code, different compilers will generate machine code with varying performance & size. Generally the more efficient machine code (uses…
- 28 Jan 2016
nRF52 Range Extension with RFaxis' RFX2411N

Floyd Ashbaugh

External Power Amplifiers and LNAs easily connected to the nRF52 series device for high power extended range operation. Data sheets, white papers, schematics and layout information available at link t…
- 26 Jan 2016
Developing Nordic nRF51 applications with mbed and Visual Studio

ivan

This tutorial shows how to use the mbed framework to develop applications for Nordic nRF51 devices. Before you begin, install VisualGDB 5.1 or later. Start Visual Studio and open the VisualGDB Embedded…
- 26 Jan 2016
PA / LNA support in S132

Einar Thorsrud

The S132 SoftDevice for the nRF52 has support for enable/disable switching of external Power Amplifiers (PA) and Low Noise Amplifiers (LNA) using GPIO pins. This was introduced in S132 version 2.0.0-7…
- 25 Jan 2016
Step by Step Guide to Setup and Start Developemt with nRF51 or nRF52 DK and IAR

Pratyush Dave

The purpose of this blog is to provide a step by step guide to help a developer, starting off with the Nordic Semiconductor nRF51 DK, to get the necessary tools installed and get the software (SW) development…
- 25 Jan 2016
BLE nrf51 - Multilink NUS central - Connect to many peripherals through NUS service - with Arduino host

Marco Russi

Hi all, I implemented a simple multilink NUS central based on s130 for nrf51 chip-set. It means that this NUS central can connect to several peripherals simultaneously and send data to each one of them…
- 24 Jan 2016