Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered

One command execution time on serialization 0

Hi, I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...

746 views

0 replies

Started over 11 years ago
by Elliot.Chao
Not Answered

Has anybody used pervasive dispalay (repaper) on NRF51822 Evaluation Kit? 0

Has anybody got it working? I ported the EPD library from Adruino EPD libray but not sure where its going wrong.

759 views

0 replies

Started over 11 years ago
by Barada Mishra
Not Answered

get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE 0

I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...

2478 views

0 replies

Started over 11 years ago
by julian
Not Answered

HOW do I erase SDK5.2 version of flash and read not, in SDK4.2 can. 0

Hello: Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...

1395 views

0 replies

Started over 11 years ago
by bugg
Not Answered

nRF24LU1 programs a byte through spi command,a strange problem occured... 0

before i write the flash, it has been erased.so ,its value is all 0xff. when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...

652 views

0 replies

Started over 11 years ago
by Albert

Recent in Nordic blog

Flashing nRF5x firmware using any dumb terminal program via standard serial COM port

Nguyen Hoan Hoang

There are times that we needed to flash the nRF5x series on a PC where the development software were not installed. The problem could be worst when network access is limited. With a HEX file on hand…
- 18 Sep 2017
How to Debug the nRF52 Interrupts — Useful Tips

Yaniv Nis

Debugging interrupts in not an easy task. During the development of Jumper's Emulator, we gather few useful tips that we think can help you all when debugging the nRF52 interrupts. Hope it will help…
- 13 Sep 2017
The ultimate guide to maximizing your BLE and Bluetooth 5 data throughput

Mohammad Afaneh

In my 2nd blog post in the series on Bluetooth 5, I go over one of the main features of Bluetooth 5: 2x speed. The advertised 2x speed of Bluetooth 5 is great! BUT, what does that even mean? Is it…
- 7 Sep 2017

Latest guides

Getting Started: Developing for the nRF52805 with nRF5 SDK

bjorn-spockeli

Introduction The nRF52805 SoC is a low-cost member of the nRF52 Series with a subset of the features of the nRF52811 and nRF52810 SoCs. As the nRF52805 has a feature subset of the nRF52810/11 SoCs, which…
- 11 Jun 2020
nRF5x: nRF52832 Specific PCB Guidelines

Andreas

This guide will cover the specific areas that must be paid extra attention to when designing a PCB for nRF52832. It is intended as a nRF52832 specific addition to the General PCB design guidelines for…
- 10 Jun 2020
Hardware design, RF test and coverage: iBasis eSIM International Coverage Update

Brian Kim

Since Nordic Semiconductor announced that it has partnered with one of the world’s largest international cellular carriers, iBASIS, to use nRF9160 System-in-Package (SiP) module and to include an iBasis…
- 4 Jun 2020
Getting started: Getting NB-IoT Demo running on Thingy:91

Christian Kurz

The Nordic Thingy:91 is a cellular IoT prototyping platform. It is based on the nRF9160 System-in-Package (SiP). The nRF9160 has an integrated modem that supports both LTE-M and NB-IoT. The factory programmed…
- 29 May 2020
Bluetooth low energy: Mocking CoreBluetooth

Aleksander Nowakowski

CoreBluetooth is the native iOS framework to communicate with Bluetooth-enabled Low Power (LE) devices, except iBeacons (which require CoreLocation) and HomeKit devices. It is easy to start with, if one…
- 9 Mar 2020
Getting Started : Build NCS application firmware images using Docker

Markus Tacker (he/him)

How to compile a NCS application using Docker so you don't need to install dependencies directly in your system.
- 17 Feb 2020