Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered

Wake-up Times ? 0

Hi, how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ? And how long does it tai if after wakeup it had to communicate...

1195 views

0 replies

Started over 11 years ago
by Nils Minor
Not Answered

What does the SWI0 do and how is it used in app_timer? 0

I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...

1061 views

0 replies

Started over 11 years ago
by Mike
Not Answered

Connect to nRF6310 0

Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart" to develop a new project, and encounter some questions... we update nRF6310...

808 views

0 replies

Started over 11 years ago
by Kadi Chang
Not Answered
RX/TX buffers in S110 0

Hello, How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval). How is it on receiving? Is it e...
- s110
- nrf51822
1216 views

0 replies

Started over 11 years ago
by Cyril Hruscak
Not Answered

How can I ensure not be Interrupted by radio when I use gpio simulate IIC? 0

My sensor is off-standard,so I have to use gpio to read and write my sensor. Gpio IIC will take about 0.5ms to get data. My app need send data every 7.5ms,it seems that...

819 views

0 replies

Started over 11 years ago
by gootoomoon

Recent in Nordic blog

Developing Nordic nRF51 applications with mbed and Visual Studio

ivan

This tutorial shows how to use the mbed framework to develop applications for Nordic nRF51 devices. Before you begin, install VisualGDB 5.1 or later. Start Visual Studio and open the VisualGDB Embedded…
- 26 Jan 2016
PA / LNA support in S132

Einar Thorsrud

The S132 SoftDevice for the nRF52 has support for enable/disable switching of external Power Amplifiers (PA) and Low Noise Amplifiers (LNA) using GPIO pins. This was introduced in S132 version 2.0.0-7…
- 25 Jan 2016
Step by Step Guide to Setup and Start Developemt with nRF51 or nRF52 DK and IAR

Pratyush Dave

The purpose of this blog is to provide a step by step guide to help a developer, starting off with the Nordic Semiconductor nRF51 DK, to get the necessary tools installed and get the software (SW) development…
- 25 Jan 2016
BLE nrf51 - Multilink NUS central - Connect to many peripherals through NUS service - with Arduino host

Marco Russi

Hi all, I implemented a simple multilink NUS central based on s130 for nrf51 chip-set. It means that this NUS central can connect to several peripherals simultaneously and send data to each one of them…
- 24 Jan 2016
SEGGER Embedded Studio Part 2 - Monitor Mode Debugging

Michael Dietz

This tutorial will take less than 15 minutes. #Motivation Never lose a BLE connection when debugging your applications again! This technique will also be useful for any application using the PWM peripheral…
- 22 Jan 2016
An introduction to error handling in nRF5 projects

Audun

As you start developing with the nRF5 series chips, SoftDevices, and SDKs, it's very useful to learn how errors can be discovered (and preferrably recovered from). This can be detecting something as simple…
- 20 Jan 2016