Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
nRF5340 PDM CLK waveform 0

Hi We use nRF5340, set GPIOs as PDM for DMIC device, and measure waveform as below The PDM DATA high level will decrease periodically Is this waveform normal? If yes...
16 views

0 replies

Started 19 hours ago
by Poki Huang
Not Answered
BLE Mesh replay protection triggered during burst vendor message transmission via GATT Proxy 0

Hello, I am developing a Bluetooth Mesh application using Nordic hardware and am running into reliability issues when transmitting bursts of vendor messages. System overview...
- development
- java
- software
- beginner
- Failure Analysis
- debugging
- android
- mesh
- configuration
- C
- nrf52840
27 views

0 replies

Started 1 day ago
by mromano
Not Answered
Integration of legacy application to NCS bare metal system 0

Hi, I have the following situation: I have a legacy C application that runs on the good old nRF5 SDK on NRF52840 with FreeRTOS. (No BLE on the application, but the bootloader...
20 views

0 replies

Started 1 day ago
by rbence
Not Answered
How to maximize Conn CTE packet rate on nRF5340? 0

Dear Nordic Specialist, I am using two nRF5340 DKs running the Direction Finding connection-based Central/Peripheral examples, and I would like to evaluate the maximum achievable...
17 views

0 replies

Started 1 day ago
by cheng
Not Answered
nRF52840 DFU System 0

Hi, you all. I am working on the DFU system with my custom BLE service. I have successfully integrated DFU into my system. I structured a system with integrating DFU into...
- development
- software
- nrf5 sdk
- nrf52840
- s140
- dfu
20 views

0 replies

Started 1 day ago
by omerBzkrt

Recent in the DevZone Blog

Intro to ShockBurst/Enhanced ShockBurst

Daniel Veilleux

The first generation of wireless PC accessories to achieve widespread success (the ones that shipped with a dongle in the box) adopted 2.4GHz radios because these radios offered the optimal trade-off between…
- 1 Jan 2018
Writing BLE firmware with a few lines of code

Nguyen Hoan Hoang

Writing a BLE firmware can now be done with a few lines of code. The code example bellow is all you need to write for a non-connectable BLE firmware that advertise a counter value every second in the…
- 29 Dec 2017
nrF52 Tutorial: ETM Instruction Trace with Keil MDK

Bob Boys

Hello I wrote a tutorial on using the nrF52 Development Kit with Keil MDK. www.keil.com/appnotes/docs/apnt_308.asp This document features essential debugging capabilities of the nrF52 series. ETM Instruction…
- 15 Dec 2017
One minute to understand BLE connection data package

viewtool

1.Profile During connection procedure of BLE, there are three packages: SCAN_REQ, SCAN_RSP 和 CONNECT_REQ。 SCAN_REQ： Scan request, issued by MASTER DEVICE, send to SLAVE DEVICE，sent by the Link Layer…
- 15 Dec 2017
One minute to understand BLE MTU data package

viewtool

1.Profile MTU: ATT Maximum Transmission Unit (MTU) is the maximum length of an ATT packet. The ATT MTU is defined by the L2CAP and can be anywhere between 23 and infinity. The implementation of the Bluetooth…
- 15 Dec 2017
Debugging on nrf52840 with GDB from CLI on linux

jfcamel

Today I tried to find the better ways to debug program on nRF52840 PDK from CLI on linux. The ways that I tried [Failed] openocd (both stlink and jlink) & gdb [Succeeded] JLink & JLinkGDBServer &…
- 14 Dec 2017