Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
peripheral_ancs_client in Zephyr on nRF5340-DK not visible in Settings->Bluetooth on iOS18 iPhones 0

I'm running the peripheral_ancs_client using the 2.9.0 SDK on a nRF5340-DK. On an iPhone running iOS18, the device is not visible under Settings->Bluetooth when the nRF5340...
- software
- Evaluation
- zephyr
- ios
- nRF5340
20 views

0 replies

Started 7 hours ago
by SmartGlassDev
Not Answered
[CONFIG] set more than once in the active context, constantly 0

This feature used to be helpful pre version 2.7 or so, but has persisted as an issue since then. All of the configs in any *.conf are all underlined and have this phrase when...
12 views

0 replies

Started 7 hours ago
by alnyland
Not Answered
error: Aborting due to Kconfig warnings FATAL ERROR: command exited with status 1 0

Nordic #Devacademy intermediate course: Ticket for exercise 2 of lesson 2 Dear Colleagues, I selected the #nRF9151-DK, since it was in the list of recommended boards for...
25 views

0 replies

Started 9 hours ago
by sonic4
Not Answered
CONFIGURE FOR NRESET P0.18 TO GPIO I/O 0

Hi everyone, I have a custom board in nrf52833. Currently, the gpios on nrf52833 are gone, except for the NReset pin (P0.18). Can I configure the NReset GPIO as a GPIO I/O...
17 views

0 replies

Started 11 hours ago
by Duong Nguyen
Not Answered
nPM1300 efficiency 0

My eval setup is PPK2(source mode) -> nPM1300EV - -> nRF54L15DK. I have my load connected to BUCK2, everything else is disabled. I'm getting higher than expected input current...
16 views

0 replies

Started 12 hours ago
by Nick_RA

Recent in Nordic blog

Driving WS2812B LEDs using I2S on the Nordic nRF52832

Mahesh Venkitachalam

In this article, I use the I2S peripheral of the Nordic nRF52832 to generate the waveforms required to drive the popular WS2812B RGB LEDs. http://electronut.in/nrf52-i2s-ws2812/
- 18 Aug 2017
Walkthrough of Nordic Thingy:52 Node.js Raspberry Pi demos

gamnes

Thingy:52 Node.js Raspberry Pi Interface This blog post is a follow up to the Nordic Thingy:52 node.js/Raspberry Pi demos blog post, and will described how you can run and what to expect from each of…
- 17 Aug 2017
ble_app_hrs_freertos running in Atollic TrueSTUDIO

jmag999

This post describes how you can get the ble_app_hrs_freertos example project running in Atollic TrueSTUDIO 8.0 on a pca10040 board. This is a managed make build, it does not rely on the makefile provided…
- 14 Aug 2017
OLED display support for nRF52832 (SSD1306, Adafruit GFX)

Mahesh Venkitachalam

Just a quick post to say that we have ported the Adafruit GFX and SSD1306 libraries to nRF52832. Currently only I2C is supported. The code can be found here: https://github.com/electronut/ElectronutLabs…
- 11 Aug 2017
I tried 5 different debugger IDEs for nRF52 and STM32. Here are my results.

Jonathan

At Jumper we’re developing tools that increase the happiness levels of embedded software developers. Our main tool to date is the Jumper Emulator. As a part of the development process we’re required to…
- 9 Aug 2017
Things you should know about Bluetooth mesh

Eirik Midttun

Bluetooth SIG has recently published a new standard, the Bluetooth mesh. The mesh capability is a significant update and enables radical new applications. This in turn means that there are significant…
- 7 Aug 2017