Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
How to Make Zephyr Coredump Module Recognize a Partition Manager Partition with Sysbuild in NCS 2.9.0? 0

I'm working with nRF5340 and nRF Connect SDK 2.9.0, using sysbuild and Partition Manager for my project. I want to enable Zephyr's coredump feature and store dumps in internal...
- development
- debugging
- flash
- configuration
- nRF5340
25 views

0 replies

Started 6 hours ago
by Ali.Ghorbani
Not Answered
Fatal error occurs when enabling flash through CONFIG_FLASH 0

I have a custom NRF9151 board with Windbond W25Q32JV flash, and some other peripherals connected. It also has GPS and LTE which I have tested and work. My UART console is...
- development
- software
- Failure Analysis
- debugging
- flash
- nRF9151
- spi
- nRF9
25 views

0 replies

Started 9 hours ago
by heisenbug
Not Answered
nRF Connect for VS Code "Fetching available SDK versions..." Stuck for >3 Days 0

Hi there, I am unable to install an SDK through VSCode while trying to take the steps outlined in the documentation. I have navigated to "Manage SDKs" under the "nRF Connect...
31 views

0 replies

Started 11 hours ago
by super.ru
Not Answered
MCU restarts when waiting for a packet in RX state. 0

Hi, I have a problem with nRF52832 after entering the radio RX state. I use a proprietary protocol with fixed packet length. Packet transmission works fine, receiving the...
27 views

0 replies

Started 13 hours ago
by MarcinB
Not Answered
High Cold Start Time for GNSS on nRF9151 DK in India 0

I am working on a wearable GPS tracking device using the nRF9151 DK and testing the GNSS example code. However, I am facing an issue with the cold start time for acquiring...
21 views

0 replies

Started 14 hours ago
by Dhanesh Baheti

Recent in Nordic blog

Serial Wire Debug Port Interface for nRF52832

gamnes

1.1 Description This documentation describes the use and initialization of the Serial Wire Debug Port (SWDP) interface when writing to or reading from Flash and SRAM of the nRF52832 Rev 1. See http:/…
- 2 Jun 2017
nRF52840 GATT Data Throughput with Zephyr RTOS

vich

Nordic has recently contributed support for the 2Mbit/s PHY, part of the Bluetooth 5.0 specification, to the Zephyr Project RTOS. The video below shows how to configure, build and test GATT data throughput…
- 2 Jun 2017
The complete tutorial for developing and debugging nRF52 applications on a Mac

Mohammad Afaneh

I realize that there are already multiple tutorials on how to configure GCC along with Eclipse or SEGGER Embedded Studio (for use on a Mac), but this tutorial goes over setting up a different IDE. The…
- 11 May 2017
Bluetooth 5 2Mbps Demo with nRF52 Series and Samsung Galaxy S8

John Leonard

Bluetooth 5 - now arriving in smartphones As we know, Bluetooth 5 was launched last December by the Bluetooth SIG. The nRF52 Series from Nordic have always had Bluetooth 5 and its arrival in the mix for…
- 9 May 2017
Setting up Segger on a mac or pc and debug - step by step for humans

Lola

Most guides out there are unclear and made for machines. Here is a full guide how to setup Segger for mac OS X with some example project from the SDK ( or even a PC but not tested), and also how to debug…
- 5 May 2017
FreeRTOS threads preview with J-Link, GDB/Eclipse

Radoslaw Koppel

Short note how to make FreeRTOS program debugging with eclipse little simpler. If you are looking the information how to configure the whole environment see this post: https://devzone.nordicsemi.com/tutorials…
- 11 Apr 2017