Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
nrfCloud Rest API provisioning is not working 0

Hello I have a custom board based on nrf9160 and I cannot claim and make REST API and JWT auth work for it. These are the steps I followed 1. https://github.com/nRFCloud...
0 views

0 replies

Started 8 hours ago
by alespit
Not Answered
Bluetooth address and settings_load() 0

Hello all, i have a problem and I hope that someone can help me. I can change the bluetooth address of the device with the following code: and this is okay. I have...
0 views

0 replies

Started 9 hours ago
by Epasta
Not Answered
Impedance Control nrf9151 RF Design 0

Hello, It has been a while since I have done any controlled impedance and was wondering if someone could provide me a quick sanity check before I continue: Here is the...
0 views

0 replies

Started 9 hours ago
by Doug K
Not Answered
nRF52840 (aQFN73) vias to bottom layer 0

Hi We use the nRF52840 (aQFN73) with a 4-layer 1.6 mm PCB for our current project. The top and bottom layers are for signals, the two internal layers are ground and power...
0 views

0 replies

Started 11 hours ago
by Michael-42
Not Answered
Using ESP32 to read current with PPK2 0

Hello, I am currently working on a project where i need to read the consumption with a PPK2 through an ESP32(use it in place of a computer). Is there by chance a pin on the...
0 views

0 replies

Started 12 hours ago
by Damyan Kotsev

Recent in Nordic blog

Creating a Keil project for a Bluetooth Mesh example (Updated for 0.10.0)

Kristian Skordal

Introduction The recently released nRF5 SDK for Bluetooth Mesh does not provide Keil project files for its example projects. Fortunately, it's relatively easy to set up your own project from scratch.…
- 19 Sep 2017
Using millis() like in Arduino.

schef

Here are two simple functions to use when you want to use timestamps for time measurement. uint32_t millis(void) { return(app_timer_cnt_get() / 32.768); } and for comperison of current with given…
- 18 Sep 2017
Flashing nRF5x firmware using any dumb terminal program via standard serial COM port

Nguyen Hoan Hoang

There are times that we needed to flash the nRF5x series on a PC where the development software were not installed. The problem could be worst when network access is limited. With a HEX file on hand…
- 18 Sep 2017

Latest guides

Software and Protocols: Automating nRF91 TLS credential management via serial port AT commands

Daniel Veilleux

I have spent a bit of time recently experimenting with different TLS credential configurations using nRF91-DKs. Eventually I got to the point where I wanted to do things like swap out the certificates…
- 10 Jan 2020
Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019