Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
nRF9151 DK External Power Supply Issue 0

Hello, as the title suggests, I have an issue when powering the nRF9151 DK with an external power supply. Normally, I power through USB, and it's fine. However, when I followed...
18 views

0 replies

Started 7 hours ago
by Yun531
Not Answered
nRF9160 SLM MQTT Connection 0

Hi all, I am using and nrf9160, in particular a thingy91. It is running 1.3.7 firmware. I have the SLM sample loaded and can sent AT commands to the device using the nRF...
30 views

0 replies

Started 10 hours ago
by KR0731
Not Answered
Zephyr sample application Mesh and nRF Mesh applicatio 0

Hello, We are working on Zephyr sample app Mesh on nRF52840dongle with nRF Mesh application. After going through the documentation and few other Q&A on the portal, I was...
- software
- Evaluation
- mesh
- zephyr
- nrf52840
23 views

0 replies

Started 11 hours ago
by gsMCHP
Not Answered
custom board 0

Hlo I have to asked that i am working with custom board of nrf5340 and i want to flash and check the rf signal by flashing through the nrf5340 development board and i am...
32 views

0 replies

Started 12 hours ago
by sunaina
Not Answered
TWIM does not recover after pull‑up power domain is cycled with nRF54L15 0

Hi all, I'm encountering an issue with the TWIM30 interface on the nRF54L15 (pins P0.03 - SDA, and P0.04 - SCL), using vanilla Zephyr v4.2.0-rc1. The setup involves external...
30 views

0 replies

Started 12 hours ago
by van.petrosyan

Recent in Nordic blog

Programming the nRF51822 Beacon Kit with the nRF51DK

Stefan Birnir Sverrisson

One way to program the nRF51822 Bluetooth Smart Beacon Kit is to use the nRF51 DK. This gives you a full scale development platform (the nRF51 DK). This blog will go thru the steps needed to program…
- 7 May 2015
Bluz, a cloud connected Bluetooth LE development kit based on the nRF51822, is live on Kickstarter

eric ely

Bluz is a brand new development kit that brings Bluetooth LE to the internet. We have paired up with Spark and ported their FW to the nrf51822, allowing Bluz to be controlled and programmed over the…
- 15 Apr 2015
nRF51 current consumption for common scenarios

Stefan Birnir Sverrisson

The following is the estimated nRF51 current consumption during advertising with the DCDC disabled. Advertising 1: TX power: +4dBm adv interval: 20ms (minimum advertising interval in normal adversising…
- 14 Apr 2015
Building kernel for RPi2 with bluetooth_6lowpan for Raspbian

Håkon Alseth

Building kernel for RPi2 with bluetooth_6lowpan In this guide, you will have two choices: Cross-compilation build Native build Choose the one that fits your needs. Cross-compilation is…
- 9 Apr 2015
Debugging with Real Time Terminal

FormerMember

In SDK 12.0.0 or later, logging/debugging over RTT is built in to the logger module NRF_LOG. To enable logging over RTT, "check" the NRF_LOG_BACKEND_SERIAL_USES_RTT option in sdk_config.h in the configuration…
- 8 Apr 2015
Accessing the BLE mesh via the particle.io (spark.io) cloud

David Edwin

Hello. I was spending the last few days to implement an interface to access the BLE mesh via the Internet. The mesh consists of devices with LEDs, which then could be turned on and off in my browser.…
- 1 Apr 2015