Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Pushing keys from KMU to ECB? 0

Hi! I'm storing a key in the KMU for use by the ECB. If I set the slot's destination address to an address in RAM, the KMU pushes the key there correctly, but if I instead...
30 views

0 replies

Started 5 hours ago
by SebastianA
Not Answered
Issue of nRF54L15’s GPIO high voltage is lower than VDD 0

Hi Support Team The VDD of customer’s nRF54L15 board is 3V, but the high voltage of P1.10 is about 1V. Did you meet this issue before? Customer needs the output high voltage...
21 views

0 replies

Started 5 hours ago
by Tom.Fu
Not Answered
Wake up main thread on any interrupt 0

Hi, Is there a way to make the main thread to execute after any interrupt? For now, I have something like this (ncs 2.7.0): in main thread : In each IRQ handlers...
16 views

0 replies

Started 6 hours ago
by Ben_Squar3d
Not Answered
When a Matter device is powered back on, how can the lock status be updated to the Apple Home? 0

If the lock's status changes while the device is powered off, causing a mismatch between the lock and the Apple Hub, how can I immediately update the status upon powering...
15 views

0 replies

Started 7 hours ago
by SunHuang
Not Answered
RES Issue with nRF54L15 QFN 0

The problem has been resolved, please ignore this post
- nRF54L15
52 views

0 replies

Started 14 hours ago
by Derek Yang

Recent in Nordic blog

Upgrade RADVD for IoT on Raspberry Pi 2

Jun Qing ZOU

The RADVD deamon in Raspberry pool is version 1.8.5 (up to Raspberry 2015-02-16). root@raspberrypi:~/radvd# apt-cache policy radvd radvd: Installed: 1:1.8.5-1 Candidate: 1:1.8.5-1 Version table…
- 25 May 2015
Workaround needed for TWI driver (nrf_drv_twi) in SDK v8.1 (TWI_COUNT missing)

Hung Bui

In SDK v8.1 we added the TWI driver (nrf_drv_twi.c). Unfortunately the nrf_drv_config.h file wasn't updated correctly with the new driver. The symptom is the error with "TWI_COUNT is missing". Here…
- 20 May 2015
Common FAQs on DFU

Hung Bui

If you are looking for a place to get started with DFU, please have a look at this presentation here and the tutorial here. In this post, we cover some in depth Q&A topics regarding Device Firmware…
- 15 May 2015

Latest guides

nRF5x: nRF52805 Specific PCB Guidelines

Andreas

This guide will cover the specific areas that must be paid extra attention to when designing a PCB for nRF52805. It is intended as a nRF52805 specific addition to the General PCB design guidelines for…
- 18 Jun 2020
Getting Started: Developing for the nRF52805 with nRF5 SDK

bjorn-spockeli

Introduction The nRF52805 SoC is a low-cost member of the nRF52 Series with a subset of the features of the nRF52811 and nRF52810 SoCs. As the nRF52805 has a feature subset of the nRF52810/11 SoCs, which…
- 11 Jun 2020
nRF5x: nRF52832 Specific PCB Guidelines

Andreas

This guide will cover the specific areas that must be paid extra attention to when designing a PCB for nRF52832. It is intended as a nRF52832 specific addition to the General PCB design guidelines for…
- 10 Jun 2020
Hardware design, RF test and coverage: iBasis eSIM International Coverage Update

Brian Kim

Since Nordic Semiconductor announced that it has partnered with one of the world’s largest international cellular carriers, iBASIS, to use nRF9160 System-in-Package (SiP) module and to include an iBasis…
- 4 Jun 2020
Getting started: Getting NB-IoT Demo running on Thingy:91

Christian Kurz

The Nordic Thingy:91 is a cellular IoT prototyping platform. It is based on the nRF9160 System-in-Package (SiP). The nRF9160 has an integrated modem that supports both LTE-M and NB-IoT. The factory programmed…
- 29 May 2020
Bluetooth low energy: Mocking CoreBluetooth

Aleksander Nowakowski

CoreBluetooth is the native iOS framework to communicate with Bluetooth-enabled Low Power (LE) devices, except iBeacons (which require CoreLocation) and HomeKit devices. It is easy to start with, if one…
- 9 Mar 2020