Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
CONFIG_NRFX_TIMER1 was assigned the value y, but got the value n. Missing dependencies: HAS_NRFX || (HAS_NRFX && 0) || ((UART_0_NRF_HW_ASYNC_TIMER = 1 || UART_1_NRF_HW_ASYNC_TIMER = 1 || UART_2_NRF_HW_ASYNC_TIMER = 1 || UART_3_NRF_HW_ASYNC_TIME 0

Im using nrf5340 with nrf connect SDK 2.6. Im trying to follow this post to evaluate hardware timer for reading saadc But I constantly am getting CONFIG_NRFX_TIMER1...
19 views

0 replies

Started 8 hours ago
by IvanR
Not Answered
Adding MCUBOOT and QSPI device to DTS causes no boot 0

I am attempting to get the SMP server sample to work on some custom hardware in order to run a BLE FOTA. I'm using NCS version 2.6.1. I'm able to build the SMP server sample...
24 views

0 replies

Started 10 hours ago
by frankenboom
Not Answered
case about nRF54L15 VS Code Flash error 0

Hi， How to resolve the following burning errors: PDK:PCA10156 0.8.1 SDK ncs v0.8.0 example :peripheral_uart Thank you for all your assistance. Kind regards, Peter...
21 views

0 replies

Started 11 hours ago
by peter.min
Not Answered
ncs 2.8.0 fails to build zephyr's bluetooth ISO_CENTRAL and ISO_PERIPHERAL samples on 52840DK 0

HW: 52840DK PCA10056 3.0.1 2023.16 NCS SDK: v2.8.0 I want to test Zephyr's BLE controller instead of the default SoftDevice controller, and the `prj.conf` of ISO_CENTRAL...
39 views

0 replies

Started 14 hours ago
by banco
Not Answered
When connecting to AWS IoT with low signal it gets stuck 0

We have devices that have low signal so they have to reconnect to AWS a lot. We have a watchdog timer with a 100s timeout that we feed every 10 seconds in the control loop...
28 views

0 replies

Started 17 hours ago
by charleshaf

Recent in Nordic blog

Introduction of SDH and SDK v15.0 software architecture

Amos Lin

The SDK software architecture has been hugely changed since SDK v13.0. With adding SDH to SDK, it provides SDH API to Enabling the SoftDevice and its event interrupt. Disabling the SoftDevice. Receiving…
- 13 Aug 2018
Bluetooth pairing vulnerability

PaKa

The Bluetooth SIG released an errata for the 4.2 and 5.0 versions of Bluetooth specification on July 23rd relating to a potential vulnerability with the pairing procedures. For Bluetooth low energy; this…
- 27 Jul 2018
Getting Started with the Thingy:52 and GCC/GDB

Daniel Veilleux

The Thingy:52 IoT Sensor Kit is a fancy development board that combines the nRF52832 SoC, a handful of sensors and user interface components, and a rechargeable battery. Although the Thingy is available…
- 20 Jul 2018

Latest guides

Software and Protocols: Automating nRF91 TLS credential management via serial port AT commands

Daniel Veilleux

I have spent a bit of time recently experimenting with different TLS credential configurations using nRF91-DKs. Eventually I got to the point where I wanted to do things like swap out the certificates…
- 10 Jan 2020
Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019