Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Configuring PIN 0.00 and P0.01 as GPIO on NRF5340 with nrf connect sdk v3.0.2 0

Hello, We upgraded our project to nrf connect sdk v3.0.2 from v2.9.0 and can no longer use pin 0.00 and pin 0.01 as gpio. The problem seems to be in the nrf53 soc.c file...
53 views

0 replies

Started 2 days ago
by byte
Not Answered
54L15 using DPPI to link 3 peripheral in different power domain 0

Hi I am developing in 54L15. Now use DPPI to link TIMER10's PUBLISH_COMPARE[3] ---> RADIO SUBSCRIBE_STOP, it works fine. Now I want to trigger a GPIO signal through...
60 views

0 replies

Started 2 days ago
by ToothlessYY
Not Answered
Bluetooth Qualification Using Nordic DNs for third party modules 0

Post: Hi Nordic Team, We are currently developing a product based on the Raytac MDBT50Q-1MV2 module, which integrates the nRF52840 SoC. Our firmware is built using the...
65 views

0 replies

Started 2 days ago
by MTB-C
Not Answered
Regarding the issue of space occupation on nrf52833 using the Secure Transport Layer (DTLS) 0

I use the security mechanism dtls based on udp communication. Can I implement it on nrf52833? How much flash and ram should be occupied at least? Is there a suggested value...
50 views

0 replies

Started 2 days ago
by Idle-xu
Not Answered
nrf9161 GNSS FIX without LTE 0

I am testing gnss without lte connectivity, which seems to work ok. Except when I get "The modem has detected a reset loop. LTE network attach is now restricted for the...
56 views

0 replies

Started 3 days ago
by Henning_I

Recent in Nordic blog

nRF52 Range Extension with RFaxis' RFX2411N

Floyd Ashbaugh

External Power Amplifiers and LNAs easily connected to the nRF52 series device for high power extended range operation. Data sheets, white papers, schematics and layout information available at link t…
- 26 Jan 2016
Developing Nordic nRF51 applications with mbed and Visual Studio

ivan

This tutorial shows how to use the mbed framework to develop applications for Nordic nRF51 devices. Before you begin, install VisualGDB 5.1 or later. Start Visual Studio and open the VisualGDB Embedded…
- 26 Jan 2016
PA / LNA support in S132

Einar Thorsrud

The S132 SoftDevice for the nRF52 has support for enable/disable switching of external Power Amplifiers (PA) and Low Noise Amplifiers (LNA) using GPIO pins. This was introduced in S132 version 2.0.0-7…
- 25 Jan 2016
Step by Step Guide to Setup and Start Developemt with nRF51 or nRF52 DK and IAR

Pratyush Dave

The purpose of this blog is to provide a step by step guide to help a developer, starting off with the Nordic Semiconductor nRF51 DK, to get the necessary tools installed and get the software (SW) development…
- 25 Jan 2016
BLE nrf51 - Multilink NUS central - Connect to many peripherals through NUS service - with Arduino host

Marco Russi

Hi all, I implemented a simple multilink NUS central based on s130 for nrf51 chip-set. It means that this NUS central can connect to several peripherals simultaneously and send data to each one of them…
- 24 Jan 2016
SEGGER Embedded Studio Part 2 - Monitor Mode Debugging

Michael Dietz

This tutorial will take less than 15 minutes. #Motivation Never lose a BLE connection when debugging your applications again! This technique will also be useful for any application using the PWM peripheral…
- 22 Jan 2016