Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
NRF53 programming by using nrfjprog-Q 0

Here is my script for programming. Does the sequence is OK? or any advice to improve? nrfjprog --eraseall nrfjprog --recover --family NRF53 --coprocessor CP_APPLICATION...
38 views

0 replies

Started 1 day ago
by Steven Wen
Not Answered
Pass a string to a variable using the command line. 0

Using the peripheral_uart example routine from the NCSv3.0 library with the 54l15 chip. 1. compilation command： west build --build-dir build . --pristine --board nrf54l15dk...
29 views

0 replies

Started 1 day ago
by yuanFang
Not Answered
The finer points of PWM on nRF52 using two chained buffers 0

I'm looking into a rare issue on the BBC micro:bit V2 which uses the nRF52833 as its (application) microcontroller. I used to be familiar with some CPUs from the 80s but my...
- pwm
- nRF52833
- hardware
- Pre-production
33 views

0 replies

Started 1 day ago
by kevinjwalters
Not Answered
Do o need ble bootloader separately 0

I have shifted from silicon labs for BLE project. In Si labs we have burn BLE bootloader and BLE application separately. Do i need to do the same here in nrf controller? If...
27 views

0 replies

Started 1 day ago
by Subham
Not Answered
I2C devices are not getting detected in NRF54L15 Dev Kit. 0

I am unable to detect any i2c device when connected to the Nordic nRF54L15 DK kit. I have change the voltage from 1.8v to 3.3v and Tried and explore other pins in Port 0 and...
- software
- beginner
- nRF Connect SDK
- debugging
- nRF54L05
- Evaluation
- Protocol
- nRF54L15
- documentation
- zephyr
- twi
29 views

0 replies

Started 1 day ago
by rsramki

Recent in Nordic blog

Motor Control over BLE with nRF51822 and TB6612FNG

Mahesh Venkitachalam

In this project, we will control two motors over BLE using the Nordic nRF51-DK. To do this, we will use a motor driver based on the Toshiba TB6612FNG chip. We will use GPIOs and PWM to communicate with…
- 5 Aug 2015
Create Hurricane Tunnel Broker on Raspberry Pi

Eugene Yu

This blog introduces how to create tunnel broker service in order to support IPv6 on your IPv4 network. The tunnel broker is providing IP conversion service with 6in4. Preparation Raspberry Pi…
- 4 Aug 2015
An appeal to makers - why you should document your project, and how you can do it

Mahesh Venkitachalam

An appeal to makers - why you should document your project, and how you can do it. http://electronut.in/why-how-document-project/
- 3 Aug 2015
ADXL 345 Tutorial

Milad

Hello all, this tutorial goes to a fellow named Emil who helped me with this project. Number 1_ Make sure you set up the terminal viewer For debugging with real.You need it to see the values coming outta…
- 1 Aug 2015
nRF51 Qt GCC Example

Jacob Portukalian

Hi Everyone! At Sky Wave Design, we recently switched all of our Nordic development over to using GCC and using Qt Creator as the IDE. We have released our example project on github for those of you…
- 31 Jul 2015
ROM and RAM Management

Øyvind Karlsen

Introduction Here are some tips and tricks to manage your application size. RAM and ROM usage The total RAM usage is: ZI-data + RW-data The total flash usage is: Code + RO-data + RW-data …
- 28 Jul 2015