Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Troubles posting to DevZone 0

I'm having a lot of new trouble posting to devzone. I can not drag/drop files. It keeps suggesting "An error occurred. Please try again or contact your administrator." This...
30 views

0 replies

Started 2 days ago
by RichM
Not Answered
Setting CONFIG_BT_CTLR_DATA_LENGTH_MAX=251 but payload is limited to 229 bytes. 0

We are running an HCI controller on nRF52833 based on the Zephyr hci_uart sample code. We are using the Zephyr 3.7.0 LTS version. We have set CONFIG_BT_CTLR_DATA_LENGTH_MAX...
33 views

0 replies

Started 2 days ago
by Mike.Redd
Not Answered
Warning FLASH_SIMULATOR unassigned starting from NCS SDK 2.7.0 due to missing default flash_sim.overlay from build 0

I have found that in NCS SDK 2.6.2 it was very simple to enable FLASH_SIMULATOR as part of the mcuboot configuration overlays. But starting from SDK 2.7.0, I keep getting...
35 views

0 replies

Started 2 days ago
by Alfredo Antolinez
Not Answered
Run time control of MCU Manager 0

We are looking to do DFU over UART to the Application as described in DevAcademy nRF Connect SDK Intermediate, Lesson 8, Exercise 1, Step 5. However, we have only one UART...
- development
- software
- dfu
- nRF5340
24 views

0 replies

Started 2 days ago
by bbbakke
Not Answered
Thingy 91x Modem_shell RTT issue 0

I am working to convert from Thingy 91 to Thingy 91x. I have successfully used the modem_shell with RTT output and control and the overlay does not seem to work with SDK 2...
23 views

0 replies

Started 2 days ago
by RichM

Recent in Nordic blog

BLEBot - a phone controlled/autonomous 2WD robot based on nRF51822

Mahesh Venkitachalam

In this project, we will build a two-wheeled robot based on the Nordic nRF51822 BLE SoC. Motor control for the two wheels of the robot will be done using an L293D chip. The robot can be controlled using…
- 12 Oct 2015
Toys 2.0: Smart Toy Robots use the nRF51 based Cannybot Brain

Wayne

The Cannybot Brain is a robotics controller board that uses the Nordic Semiconductor nRF51822 at its core. The board has been developed by Cannybots Limited in Cambridge, UK. One of Cannybots core values…
- 6 Oct 2015
Programming services, HI-LO Electronics in corporation with Nordic Semiconductor AS

HILO

In corporation with Nordic Semiconductor we are happy to announce our programming services! Your flexible programming center is based in Gothenburg, Sweden at HI-LO Electronics AB Advantages with pre…
- 30 Sep 2015

Latest guides

Software and Protocols: Automating nRF91 TLS credential management via serial port AT commands

Daniel Veilleux

I have spent a bit of time recently experimenting with different TLS credential configurations using nRF91-DKs. Eventually I got to the point where I wanted to do things like swap out the certificates…
- 10 Jan 2020
Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019