Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
nRF54l15 Making Use of Low Power Mode and an External Crystal Oscillator 0

Hi Nordic Team, I have developed a couple applications for the nRF52833 using Zephyr and have now moved to the nRF54l15. For this new application, power consumption is...
- development
- software
- nRF54L15
- zephyr
- low-power
37 views

0 replies

Started 1 day ago
by LeviRand
Not Answered
nRF54L15 hfclk does not power down after i2c sensor device_init fails 0

Hi, I have question about a project I'm running on nRF connect sdk 2.9.1. I noticed that whenever an i2c sensor device device_init() is returning a value not equal...
- development
- software
- nRF54L15
- zephyr
34 views

0 replies

Started 1 day ago
by Ypenburg
Not Answered
nRF Connect examples for Thingy:91 X 0

I am trying to run some of the more basic examples included in the nRF Connect SDK on the nRF5340 included in a Thingy:91 X . I have installed the latest version of the nRF...
38 views

0 replies

Started 1 day ago
by Scott Grubb
Not Answered
Change CPU frequency of nRF54L15 0

The OSCILLATORS documentation says: " The device starts at 64 MHz. For 128 MHz, it must be configured when the CPU starts and before any peripherals that use the high-frequency...
33 views

0 replies

Started 2 days ago
by Emil Lenngren
Not Answered
Disable CCC attribute changed callback in the running time 0

Hello, I am using nRF54l15 and nRF Connect SDK v2.9.0 I need to know if there is any way to disable the cfg_changed callback at runtime. I want it to be called in case...
30 views

0 replies

Started 2 days ago
by Nedaa_H_Ahmed

Recent in Nordic blog

Serial Wire Debug Port Interface for nRF52832

gamnes

1.1 Description This documentation describes the use and initialization of the Serial Wire Debug Port (SWDP) interface when writing to or reading from Flash and SRAM of the nRF52832 Rev 1. See http:/…
- 2 Jun 2017
nRF52840 GATT Data Throughput with Zephyr RTOS

vich

Nordic has recently contributed support for the 2Mbit/s PHY, part of the Bluetooth 5.0 specification, to the Zephyr Project RTOS. The video below shows how to configure, build and test GATT data throughput…
- 2 Jun 2017
The complete tutorial for developing and debugging nRF52 applications on a Mac

Mohammad Afaneh

I realize that there are already multiple tutorials on how to configure GCC along with Eclipse or SEGGER Embedded Studio (for use on a Mac), but this tutorial goes over setting up a different IDE. The…
- 11 May 2017

Latest guides

Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019
nRF5x: Automating Power Profiler Kit measurements from the command line

Daniel Veilleux

Nordic's Power Profiler Kit (PPK) is an inexpensive piece of hardware that can provide a significant amount of insight into the operation and performance of your project. Although there is a lot that…
- 2 Aug 2019