Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
LFXO active with 0.5μA higher current 0

Hi, On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher. I am using a nRF52832 module with the low frequency crystal oscillator...
- nrf52
- s132
- lfxo
675 views

0 replies

Started over 7 years ago
by ALE
Not Answered

Wouldn't update connection params 0

Hi, I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init: static void conn_params_init(void){ uint32_t err_code; ble_conn_params_init_t...

723 views

0 replies

Started over 7 years ago
by Alice
Not Answered
how to use whitelist in ble_app_hrs_c 0

S130, SDK 12.3, ble_app_hrs_c example. I want to use whitelist function in this example but I can't finish it. When I run peer_list_get(), it gets all 0xFF, means that...
- s130
- whitelist
- ble_app_hrs_c
- nrf51822
885 views

0 replies

Started over 7 years ago
by kamisen
Not Answered

services size is zero 0

sometime,i use android app to scan ble device,it will display "the device dose not has required services",the gatt.getServices.size is zero.why?

545 views

0 replies

Started over 7 years ago
by nowen
Not Answered
one wire library for nrf51822 keil 0

one wire library for nrf51822 keil for connected ds18b20 .
- nrf51822 keil one wire
759 views

0 replies

Started over 7 years ago
by morteza1994

Recent in Nordic blog

Step by Step Guide to Setup and Start Developemt with nRF51 or nRF52 DK and IAR

Pratyush Dave

The purpose of this blog is to provide a step by step guide to help a developer, starting off with the Nordic Semiconductor nRF51 DK, to get the necessary tools installed and get the software (SW) development…
- 25 Jan 2016
BLE nrf51 - Multilink NUS central - Connect to many peripherals through NUS service - with Arduino host

Marco Russi

Hi all, I implemented a simple multilink NUS central based on s130 for nrf51 chip-set. It means that this NUS central can connect to several peripherals simultaneously and send data to each one of them…
- 24 Jan 2016
SEGGER Embedded Studio Part 2 - Monitor Mode Debugging

Michael Dietz

This tutorial will take less than 15 minutes. #Motivation Never lose a BLE connection when debugging your applications again! This technique will also be useful for any application using the PWM peripheral…
- 22 Jan 2016

Latest guides

Peripherals And RF Test: Adding a Peripheral(SPI) to an NCS (version 1.x) Zephyr project

Jeff4BLE

Objectives Provide a brief primer to NCS and Zephyr Provide a quick-start guide to adding peripherals to an existing sample project Demonstrate running both foreground and background tasks within Zephyr…
- 21 Feb 2021
Getting started: How to add DFU support to your Thingy:91 project

Didrik Rokhaug

Note: From nRF Connect SDK v1.7.0 onwards, if you build for the thingy91_nrf9160_ns or thingy91_nrf52840, everything in this guide is already done automatically. Since that SDK release, the board files…
- 21 Jan 2021
Software: Enter the Multi-NUS: A Simple Wireless UART Network

matt.heins

If you’re thinking about building a network of sensors and you begin to survey the options, you’re likely to encounter a frothing sea of acronyms representing a variety of standards and protocols clamoring…
- 12 Jan 2021
Software and Protocols: nRF9160 DK: Offloading Bluetooth Low Energy related tasks to nRF52840 SoC

Anders Storro

Background Some time ago I was working on a project that involved communication between Bluetooth mesh and a home automation platform. The goal of this project was to enable control and observability of…
- 12 Jan 2021
Bluetooth low energy: How to update advertising data dynamically using BLE Advertising library

Karl Ylvisaker

Introduction The question of how to update advertising data dynamically using the BLE Advertising library has been raised many times by our forum-goers, especially after the release of nRF5 SDK v15.2.0…
- 6 Jan 2021
Software: Device Firmware Update (DFU) with MCUBoot bootloader

Mark Q

Purpose The purpose of this blog is to show how to create a Zephyr application that boots from the MCUBoot bootloader. We will also show how to update an application using the Device Firmware Update (DFU…
- 3 Nov 2020