Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
BLE Connection Issues with nRF52832 Multi-Device Setup 0

We are currently developing a project using the nRF52832 as the microcontroller, Segger Embedded Studio version 5.42a as the IDE, and the nRF5 SDK 17.0.2. We began by creating...
16 views

0 replies

Started 2 days ago
by siltvm
Not Answered
SDK2.9.0 - QSPI and TWI driver power management (CONFIG_PM_DEVICE_RUNTIME) 0

Hi. After migration from SDK2.7.0 to SDK2.9.0 I have issues with power mangement. CONFIG_PM_DEVICE_RUNTIME=y, which I used, causes that twi driver doesn't start. I try to...
27 views

0 replies

Started 2 days ago
by PW
Not Answered
Assistance with NB IoT Sim in India 0

Hi Community Greetings, I bought nrf9151 DK module looking at the features, power consumption & size but the fact that NB IOT has a communication rate of 15mins once in...
- development
- nRF9160
- nb-iot
- Evaluation
- nRF9151
- configuration
33 views

0 replies

Started 2 days ago
by Medcuore
Not Answered
Does the RAM power-down library support nRF9160? 0

Hello everyone. I am developing a custom board using the nRF9160. I tried using the RAM power-down library based on the Power optimization recommendations page of the nRF...
28 views

0 replies

Started 2 days ago
by matsuura
Not Answered
nRF9160 Reserved pins in footprint 0

Since the nRF9160 reserved pins are never used, Is there any issue leaving them out of the footprint? I would place copper keepouts under the reserved pin areas to ensure...
40 views

0 replies

Started 3 days ago
by gwagner_emf

Recent in Nordic blog

#HackDublin article with videos

Eirik Midttun

I recently blogged about Nordic and Hackathons, but didn't include too much information; I knew already there was something coming. And now it is finally published: #HackDublin - Ireland's First Design…
- 15 Dec 2014
QuickLogic Announces TAG-N Wearable Sensor Hub Eval Kit

QuickLogic

Today, QuickLogic announced the availability of our TAG-N Wearable Sensor Hub evaluation kit for the Nordic Semi nRF51 DK, Nordic’s all-in-one, multiprotocol development kit for ultra-low power wireless…
- 11 Dec 2014
Native support for nRF51 SDK in Keil IDE

Krzysztof Loska

Recently we introduced support for CMSIS-Pack into our nRF51 SDK. The nRF51 SDK is natively supported in the Keil IDE. This means that nRF51 SDK latest version and example software for nRF51 are easily…
- 10 Dec 2014

Latest guides

Software: Using nRF Connect SDK and west to compile and program the DTM example into the nRF52840 DK

Jay Tyzzer

Background There is a need to enable Nordic hardware with the Direct Test Mode (DTM) firmware. This is so the physical layer and RF characteristics may be ascertained as set in the Bluetooth Sig Specification…
- 14 Apr 2022
Software Development Kit: nRF5 SDK v17.1.0 Secure DFU Hands-on Tutorial for the nRF52810

notsane0

Requirements This document uses: Segger Embedded Studio (SES) nRF5 SDK v17.1.0 an nRF52 DK to emulate the nRF52810 a BLE-enabled mobile device You may want to review the blog here for a more comprehensive…
- 8 Apr 2022
Software Development Kit: nRF5 SDK v17.1.0 Secure DFU Hands-on Tutorial

notsane0

Requirements This hands-on tutorial uses: Segger Embedded Studio (SES) nRF5 SDK v17.1.0 an nRF52840 DK a BLE-enabled mobile device You can use an nRF52 DK or nRF52833 DK instead of the nRF52840 DK,…
- 8 Apr 2022
Software: Building a Bluetooth application on nRF Connect SDK - Part 3 Optimizing the connection

Hung Bui

This is part 3 of the series Building a Bluetooth application on nRF Connect SDK You can find other parts here: Part 1 - Peripheral Role. Part 2 - Central Role. In Part 1 we covered the generic architecture…
- 21 Feb 2022
Peripherals And RF Test: Using Bluetooth Shell

Mark Q

Purpose The purpose of this guide is to demonstrate the use of Bluetooth Shell. Bluetooth Shell (BT Shell) is a command-line shell application that runs over the UART. It allows one to manually type in…
- 21 Jan 2022
Software: Memory Optimization with the nRF Connect SDK

matt.heins

Out of the box, the examples in the nRF Connect SDK are configured for ease of use, functionality, and debugging; they are not generally configured for optimal memory utilization. Some of the examples…
- 6 Jan 2022