Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered

OpenOCD with nRF52 and Olimex debugger 0

I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...

2288 views

0 replies

Started over 8 years ago
by Tosa
Not Answered

nRF24LE1 (multiple) to nRF24L01 (1) sample RF projects? 0

Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...

1322 views

0 replies

Started over 8 years ago
by mr_creosote
Not Answered

task time of radio from DISABLE to RX 0

HI: i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow: while (1) { Rf_StartRx(ReciverSC.RfBufPointer...

543 views

0 replies

Started over 8 years ago
by baicai
Not Answered

nrf51822 and tmp102 0

Hi to everyone, i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822. I want to read the values of the sensor over a beacon app. ...

579 views

0 replies

Started over 8 years ago
by Roberto
Not Answered

After DFU, the device can't reset 0

Hi,I'm glad you can see my post. Now, I am in a program to read and write FLASH such as the screenshot in the attachment. Then I update with DFU service for the equipment...

754 views

0 replies

Started over 8 years ago
by ymYin

Recent in Nordic blog

Serial Wire Debug Port Interface for nRF52832

gamnes

1.1 Description This documentation describes the use and initialization of the Serial Wire Debug Port (SWDP) interface when writing to or reading from Flash and SRAM of the nRF52832 Rev 1. See http:/…
- 2 Jun 2017
nRF52840 GATT Data Throughput with Zephyr RTOS

vich

Nordic has recently contributed support for the 2Mbit/s PHY, part of the Bluetooth 5.0 specification, to the Zephyr Project RTOS. The video below shows how to configure, build and test GATT data throughput…
- 2 Jun 2017
The complete tutorial for developing and debugging nRF52 applications on a Mac

Mohammad Afaneh

I realize that there are already multiple tutorials on how to configure GCC along with Eclipse or SEGGER Embedded Studio (for use on a Mac), but this tutorial goes over setting up a different IDE. The…
- 11 May 2017

Latest guides

Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019
nRF5x: Automating Power Profiler Kit measurements from the command line

Daniel Veilleux

Nordic's Power Profiler Kit (PPK) is an inexpensive piece of hardware that can provide a significant amount of insight into the operation and performance of your project. Although there is a lot that…
- 2 Aug 2019