Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
How to get APP_ERROR_CHECK(err_code) to print out error msg instead of reset? 0

I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
- 130 sdk11 ble
- bluetooth low energy
1442 views

0 replies

Started over 8 years ago
by helpme
Not Answered
ble_app_uart does not support DFU(Device Firmware Update) 0

Hello All, I have problem with ble_app_uart which are not support DFU services. When I am implement both services device will not advertise. and when ble_nus uninitialized...
- nrf52
- ble_uart
- ble
- nrf51
- dfu
- ble_nus
1005 views

0 replies

Started over 8 years ago
by Rajneesh
Not Answered
Device not start after Bootloader/SoftDevice 0

[symptom] I want to update my application/bootloader/softdevice by DFU. Steps are shown below. bootloder/softdevice update if 1 step is done, application update...
- dfu
672 views

0 replies

Started over 8 years ago
by shtsht
Not Answered
Help needed to setup a 15 channel ANT network on the nRF52 development kit 0

Dear Developer Zone, I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
- nrf52 dk s332
1355 views

0 replies

Started over 8 years ago
by Colt
Not Answered
ESB Sources and how to change them 0

Hello, i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
- esb
991 views

0 replies

Started over 8 years ago
by florian2840

Recent in Nordic blog

BLEBot - a phone controlled/autonomous 2WD robot based on nRF51822

Mahesh Venkitachalam

In this project, we will build a two-wheeled robot based on the Nordic nRF51822 BLE SoC. Motor control for the two wheels of the robot will be done using an L293D chip. The robot can be controlled using…
- 12 Oct 2015
Toys 2.0: Smart Toy Robots use the nRF51 based Cannybot Brain

Wayne

The Cannybot Brain is a robotics controller board that uses the Nordic Semiconductor nRF51822 at its core. The board has been developed by Cannybots Limited in Cambridge, UK. One of Cannybots core values…
- 6 Oct 2015
Programming services, HI-LO Electronics in corporation with Nordic Semiconductor AS

HILO

In corporation with Nordic Semiconductor we are happy to announce our programming services! Your flexible programming center is based in Gothenburg, Sweden at HI-LO Electronics AB Advantages with pre…
- 30 Sep 2015

Latest guides

Software: Using nRF Connect SDK and west to compile and program the DTM example into the nRF52840 DK

Jay Tyzzer

Background There is a need to enable Nordic hardware with the Direct Test Mode (DTM) firmware. This is so the physical layer and RF characteristics may be ascertained as set in the Bluetooth Sig Specification…
- 14 Apr 2022
Software Development Kit: nRF5 SDK v17.1.0 Secure DFU Hands-on Tutorial for the nRF52810

notsane0

Requirements This document uses: Segger Embedded Studio (SES) nRF5 SDK v17.1.0 an nRF52 DK to emulate the nRF52810 a BLE-enabled mobile device You may want to review the blog here for a more comprehensive…
- 8 Apr 2022
Software Development Kit: nRF5 SDK v17.1.0 Secure DFU Hands-on Tutorial

notsane0

Requirements This hands-on tutorial uses: Segger Embedded Studio (SES) nRF5 SDK v17.1.0 an nRF52840 DK a BLE-enabled mobile device You can use an nRF52 DK or nRF52833 DK instead of the nRF52840 DK,…
- 8 Apr 2022
Software: Building a Bluetooth application on nRF Connect SDK - Part 3 Optimizing the connection

Hung Bui

This is part 3 of the series Building a Bluetooth application on nRF Connect SDK You can find other parts here: Part 1 - Peripheral Role. Part 2 - Central Role. In Part 1 we covered the generic architecture…
- 21 Feb 2022
Peripherals And RF Test: Using Bluetooth Shell

Mark Q

Purpose The purpose of this guide is to demonstrate the use of Bluetooth Shell. Bluetooth Shell (BT Shell) is a command-line shell application that runs over the UART. It allows one to manually type in…
- 21 Jan 2022
Software: Memory Optimization with the nRF Connect SDK

matt.heins

Out of the box, the examples in the nRF Connect SDK are configured for ease of use, functionality, and debugging; they are not generally configured for optimal memory utilization. Some of the examples…
- 6 Jan 2022