Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Internal flash as a Non volatile storage for user data 0

Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash. External Flash memory has a lot of drawback in comparsion with internal...
- flash pstorage
1301 views

0 replies

Started over 8 years ago
by PanTikTak
Not Answered
List of available peripherals 0

Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]? I am using NRF5182...
- list
- peripheral
- nrf51822
- scan
848 views

0 replies

Started over 8 years ago
by Punit
Not Answered
How to get APP_ERROR_CHECK(err_code) to print out error msg instead of reset? 0

I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
- 130 sdk11 ble
- bluetooth low energy
1474 views

0 replies

Started over 8 years ago
by helpme
Not Answered
ble_app_uart does not support DFU(Device Firmware Update) 0

Hello All, I have problem with ble_app_uart which are not support DFU services. When I am implement both services device will not advertise. and when ble_nus uninitialized...
- nrf52
- ble_uart
- ble
- nrf51
- dfu
- ble_nus
1028 views

0 replies

Started over 8 years ago
by Rajneesh
Not Answered
Device not start after Bootloader/SoftDevice 0

[symptom] I want to update my application/bootloader/softdevice by DFU. Steps are shown below. bootloder/softdevice update if 1 step is done, application update...
- dfu
704 views

0 replies

Started over 8 years ago
by shtsht

Recent in Nordic blog

Flashing nRF5x firmware using any dumb terminal program via standard serial COM port

Nguyen Hoan Hoang

There are times that we needed to flash the nRF5x series on a PC where the development software were not installed. The problem could be worst when network access is limited. With a HEX file on hand…
- 18 Sep 2017
How to Debug the nRF52 Interrupts — Useful Tips

Yaniv Nis

Debugging interrupts in not an easy task. During the development of Jumper's Emulator, we gather few useful tips that we think can help you all when debugging the nRF52 interrupts. Hope it will help…
- 13 Sep 2017
The ultimate guide to maximizing your BLE and Bluetooth 5 data throughput

Mohammad Afaneh

In my 2nd blog post in the series on Bluetooth 5, I go over one of the main features of Bluetooth 5: 2x speed. The advertised 2x speed of Bluetooth 5 is great! BUT, what does that even mean? Is it…
- 7 Sep 2017

Latest guides

Getting Started: Developing for the nRF52805 with nRF5 SDK

bjorn-spockeli

Introduction The nRF52805 SoC is a low-cost member of the nRF52 Series with a subset of the features of the nRF52811 and nRF52810 SoCs. As the nRF52805 has a feature subset of the nRF52810/11 SoCs, which…
- 11 Jun 2020
nRF5x: nRF52832 Specific PCB Guidelines

Andreas

This guide will cover the specific areas that must be paid extra attention to when designing a PCB for nRF52832. It is intended as a nRF52832 specific addition to the General PCB design guidelines for…
- 10 Jun 2020
Hardware design, RF test and coverage: iBasis eSIM International Coverage Update

Brian Kim

Since Nordic Semiconductor announced that it has partnered with one of the world’s largest international cellular carriers, iBASIS, to use nRF9160 System-in-Package (SiP) module and to include an iBasis…
- 4 Jun 2020
Getting started: Getting NB-IoT Demo running on Thingy:91

Christian Kurz

The Nordic Thingy:91 is a cellular IoT prototyping platform. It is based on the nRF9160 System-in-Package (SiP). The nRF9160 has an integrated modem that supports both LTE-M and NB-IoT. The factory programmed…
- 29 May 2020
Bluetooth low energy: Mocking CoreBluetooth

Aleksander Nowakowski

CoreBluetooth is the native iOS framework to communicate with Bluetooth-enabled Low Power (LE) devices, except iBeacons (which require CoreLocation) and HomeKit devices. It is easy to start with, if one…
- 9 Mar 2020
Getting Started : Build NCS application firmware images using Docker

Markus Tacker (he/him)

How to compile a NCS application using Docker so you don't need to install dependencies directly in your system.
- 17 Feb 2020