Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
RES Issue with nRF54L15 QFN 0

The problem has been resolved, please ignore this post
- nRF54L15
57 views

0 replies

Started 2 days ago
by Derek Yang
Not Answered
NFC library code for type 4 NDEF card emulation : cannot disable nfc after enabling, or redo setup to change to (say) type 2 or ADPU handling config without ASSERT() 0

Smartbadge epaper custom board using nrf5340/nrf7002, with an NFC loop to allow NFC card emulation/communication. Building using NCS2.9 with sysbuild. I want to be able...
22 views

0 replies

Started 2 days ago
by BrianW
Not Answered
I am developing with the nRF54L15 DK, but the code do not run stable, what can it be? 0

The nRF54L series is a new device to the nRF family, and during the bring-up of the chip from early engineering samples to mass production devices there have been quite a...
162 views

0 replies

Started 22 days ago
by Kenneth
Not Answered
BLE audio from nrf5340 to Samsung Galaxy Buds3 0

Hello. I am trying to implement stable connection between my nordic nrf5340 and Samsung Galaxy Buds3 earbuds. I did it based on ble audio example with two connections (one...
94 views

0 replies

Started 1 month ago
by mib383
Not Answered
-removed- 0

-removed-
- software
- nrf5 sdk
- bluetooth le
- nrf52840
- s140
- dfu
- production
97 views

0 replies

Started 1 month ago
by rbmarcus

Recent in Nordic blog

Step by Step Guide to Setup and Start Developing with the nRF51 DK and Keil

Pratyush Dave

The purpose of this blog is to provide a step by step guide to help a developer, starting off with the Nordic Semiconductor nRF51 DK, get the tools installed and get the software (SW) development environment…
- 17 Jun 2015
Debugging using QtCreator on Mac

wim

This post started as a question, but got the suggestion to post this as a blog post. Here it is. I have been trying to get QtCreator configured such that I can use it as my IDE for the nrf51822 on Mac…
- 12 Jun 2015
Trying OpenWRT Chaos Calmer (15.05 RC1) on Raspberry Pi 2

Jun Qing ZOU

| |.-----.-----.-----.| | | |.----.| |_ | - || _ | -__| || | | || _|| _| |_______|| __|_____|__|__||________||__| |____| |__| W I R E L E S S F R E E D…
- 11 Jun 2015

Latest guides

Software and Protocols: Automating nRF91 TLS credential management via serial port AT commands

Daniel Veilleux

I have spent a bit of time recently experimenting with different TLS credential configurations using nRF91-DKs. Eventually I got to the point where I wanted to do things like swap out the certificates…
- 10 Jan 2020
Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019