Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered

Does SoftDevice use AAR and CCM if pairing / bonding is not in use? 0

Hello, I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...

496 views

0 replies

Started over 8 years ago
by Paolo D
Not Answered

Can I use a ancs service in nrf51822, connect to android 0

Can I use a ancs service in nrf51822, connect to android device? Or I need another service in my device?

379 views

0 replies

Started over 8 years ago
by quentin
Not Answered
Clickable case for nrf51822 0

Hi Guys, I know this is more for software issues. But I was curious as to where I can find trusted case providers/makers for the nrf51822 Beacon. Can anyone from the community...
- nrf51822
1066 views

0 replies

Started over 8 years ago
by po5i
Not Answered
Sharp memory LCD library 0

Hi, Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51? Could you please advise on how to convert this Arduino...
- lcd library
1277 views

0 replies

Started over 8 years ago
by LK13131
Not Answered
Some questions/maximum ratings for nRF52 ADC device 0

Hi all, I have a few questions: How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc... The datasheet has "typical...
- nrf52 adc noise maximum rating
919 views

0 replies

Started over 8 years ago
by Therm

Recent in Nordic blog

NFC tag antenna tuning

FormerMember

NFC principle A NFC system consists of two devices, an active and a passive device. The active device is powered, and induces a magnetic field with a coil inductor antenna. When the passive device is placed…
- 20 Jun 2016
NRF52 debugging with QtCreator on Windows

Globuloz

Hello I succeeded to configure QtCreator toolchain to compile and debug my NRF52 board. So I wanted to share. I use my own Makefile to compile everything so I will focus here on how to run a debug session…
- 17 Jun 2016
BLE-Cube — A Bachelor Project

BLE Cube

In spring 2016 four students from NTNU got an assignment from Nordic Semiconductor. To compliment this assignment, the students wrote a short article: "What if controlling household appliances with your…
- 15 Jun 2016

Latest guides

Software and Protocols: Automating nRF91 TLS credential management via serial port AT commands

Daniel Veilleux

I have spent a bit of time recently experimenting with different TLS credential configurations using nRF91-DKs. Eventually I got to the point where I wanted to do things like swap out the certificates…
- 10 Jan 2020
Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019