Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
asynchronous pulse counting in low power mode 0

Hello, I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode. Pulses are asynchronous The rate of pulses can...
1077 views

0 replies

Started over 9 years ago
by fakufaku
Not Answered
nRF52 SAADC gain error a function of Vcc? 0

Hi I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52. Both the reference resistor and the PT-100 is sampled while the voltage...
- nrf52
- adc
- gain
- vcc
- nrf52382
- saadc
2249 views

0 replies

Started over 9 years ago
by Visti Andresen
Not Answered
Sample multiple inputs with fixed rate using ADC hal 0

Hi I have been searching the forums, but were not able to find an answer to my question. I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
- adc
- oftdevice
1269 views

0 replies

Started over 9 years ago
by Phillip
Not Answered

NRF24L01 sends 0

Hi I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...

563 views

0 replies

Started over 9 years ago
by Mani
Not Answered

What values can the nRF905 status register have? 0

Hi I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...

653 views

0 replies

Started over 9 years ago
by Pieter Roos

Recent in Nordic blog

SD card interfacing

Salman

Hi, I have written SD & SDHC card routine for reading, writing and erasing data from SD card. It used the hardware SPI of nRF51822. NOTE: 1)Define the PINs of SD card first before initialing. 2)Define…
- 10 Oct 2014
How different BLE packet types influence throughput

Stefan Birnir Sverrisson

There are several types of write operations, write request with authorization, write request without authorization and write command. You can see message sequence charts for those messages here and he…
- 9 Oct 2014
Measuring Lithium battery voltage with nRF51

Stefan Birnir Sverrisson

Here is an example of a hardware setup to measure the voltage on a Lithium battery with a voltage divider and a connected capacitor. The Lithium battery typically has a voltage range of 2.7 - 4.2 V and…
- 2 Oct 2014

Latest guides

Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019
nRF5x: Automating Power Profiler Kit measurements from the command line

Daniel Veilleux

Nordic's Power Profiler Kit (PPK) is an inexpensive piece of hardware that can provide a significant amount of insight into the operation and performance of your project. Although there is a lot that…
- 2 Aug 2019